Jump to content
SAU Community

Respray

K_E_V_I_N

By K_E_V_I_N,
in Western Australia

 Share

Recommended Posts

K_E_V_I_N Collaborator

K_E_V_I_N

Posted
Posted (edited)

Ok, i'm Seriously thinking about a respray for my R33 (It's black). It only has very minor dents

and some kind of paint reaction on the roof. I'm going to get a few quotes today. I

need to know roughfly how much this is going to cost me? just so i have a figure in mind.

Thanks , Kev

Edited by K_E_V_I_N
Link to comment
https://www.sau.com.au/forums/topic/151728-respray/
Share on other sites
miss_petepie Grand Master

miss_petepie

Posted
Posted

respray will cost u anythin between $1500-3k for a basic job.

I'd advise u to spend a bit more and not go for the cheapest option cos after "2 aussie summers" u will have regreted goin for the cheaper option when ur painted is faded and starting to blister and u end up havin to spend the same amount or more again to rectify the paint defects.

mike

Link to comment
https://www.sau.com.au/forums/topic/151728-respray/#findComment-2825291
Share on other sites
K_E_V_I_N Collaborator

K_E_V_I_N

Posted
  • Author
Posted
respray will cost u anythin between $1500-3k for a basic job.

I'd advise u to spend a bit more and not go for the cheapest option cos after "2 aussie summers" u will have regreted goin for the cheaper option when ur painted is faded and starting to blister and u end up havin to spend the same amount or more again to rectify the paint defects.

mike

Yeah, good point. Went out to get some quotes........ and came back with a sub & Amp >_<

Link to comment
https://www.sau.com.au/forums/topic/151728-respray/#findComment-2825387
Share on other sites
Guest
This topic is now closed to further replies.
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      New kid on the block

      By GTSBoy · Posted

      The wiring diagram for the R33 RB25 is freely available, and is essentially the same same as most other RBs (just with differences as to which pin # does which job). To get the ECU to power up, you just need to provide power to the ECCS relay, and have the other power feeds that come in from the top left of the wiring diagram (wrt the ECU) that give perma power to the fuel pump relay, the ECU itself, etc etc, all connected. When you put power on all these it will just come to life. It's pretty clear from the diagram what needs to happen. Just follow the lines from the 12V + supply stuff in the top left over towards the ECU. I've even posted snips of such diagrams (not for vanilla 25, I think for Neo and 26) to various threads here in the last few months, talking about what it takes to get the fuel pump and FPCM up and going. Search these up and they will help get you started on doing the same with the vanilla 25 diagram. Hell, for all I know, I've done the same with that one in years past and have forgotten.
    • Duncan
      New kid on the block

      By Duncan · Posted

      Yep...so unless someone posts up the answer you will need to probe from the ECU connector to the dash plug with a multi meter in continuity mode to trace the wires.  Note the ECU has multiple - and + (and across different key settings - Battery, IGN and Start) and most likely the power is fed from the connector(s) that is normally near the left hand headlight.
    • Songo
      New kid on the block

      By Songo · Posted

      Thanks Duncan, I am actually just trying to get the Rb turning and running with the RB25DET S2 original loom itself  I am just trying to get it going outside the body and not thinking about the S15 or trying to match anything to the S15 loom at all I am only trying to see if anyone has done this and what pin they found to be the ignition trigger and ECU+/- on the dash connector, that's about it. Thanks  
    • iain_ST44GA
      M35 VQ25DET starter motor

      By iain_ST44GA · Posted

      Hi Guys, Does anyone know any aftermarket part numbers for a starter motor to suit the VQ25DET? I can find lots of alternative part number for the VQ35DE, which I assume would fit, but there is a lot of conflicting information out there. Thanks..
    • Murray_Calavera
      R33 GTR running -9 with no tune

      By Murray_Calavera · Posted

      I don't understand how this hasn't boiled down to - Upgrade the turbo when you have everything required. ECU, injectors, fuel pump, turbo, etc. Do it all at once.  If you don't have everything required, just enjoy the car as it is and keep saving up your pennies. 
×
×
  • Create New...