Jump to content
SAU Community

Recommended Posts

  • Replies 45
  • Created
  • Last Reply

Top Posters In This Topic

NAr not skins, whole new cars, Whiplash has been using an Aston Martin DBR9, & a Ferrari F40 :laugh:

my bad, wrong link

http://forum.rscnet.org/forumdisplay.php?f=1116

gives you an idea where to grab them from.

as it's an official site illeagal copies seem to be off lmits but they still tell ou what to kind of search for.

Cheers

Link to comment
https://www.sau.com.au/forums/topic/152580-gtr-2/page/2/#findComment-2880472
Share on other sites

at the moment there is a C6R, Pigani Zonda, Ultima GTR, Mc Laren Longtail for the public. the dbr9 is being made by the same guys that did these and hasn't been released yet link

http://www.austraracing.com/shared/misc/WS...tmasEdition.rar

I'm part of a commercial game development team that does a few free mods for the community hence the f40 which will be released soonish. :laugh:

pics of our F40

http://forum.rscnet.org/showpost.php?p=336...amp;postcount=8

Link to comment
https://www.sau.com.au/forums/topic/152580-gtr-2/page/2/#findComment-2881259
Share on other sites

Nice one thanks! 'downloading now'

New times 'starting to get competitive now! :laugh:'

Bugatti: 1:33.810

Saleen S7

I reckon I can shave off another .6 with my current car set up, but might have to further tweak car setting for a better time. It’s a bloody hard track to get all corners perfect, certainly can’t do them all good in a single lap just yet. I just did like 15 laps & my 4th lap was the fastest :|

Link to comment
https://www.sau.com.au/forums/topic/152580-gtr-2/page/2/#findComment-2881373
Share on other sites

lol now i might clear off the desk and get the steering wheel out. Will have to use a standard car as the f40 has more power (going into turn 1 at bugatti at 300+) is lighter just badly suffers under brakes and in the aero so i'll keep a level playing field :blink:

have to organize a SAU online race sometime :P

Link to comment
https://www.sau.com.au/forums/topic/152580-gtr-2/page/2/#findComment-2881426
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Have you done the Ignition Sync Wizard in the AEM software?
    • Find out what RPM it was idling at with the IACV unplugged. It's very weird that the rpm didn't change at all, and then it stalled. When it stalls is it nearly like a switch off, like you've turned the engine off? Or is it more stutters and sputters and coughs to death over a few seconds? Or does the RPM just slowly keep going down and down? Have you done a test of trying to start it with the AFM unplugged? Does it still die?     If you Follow Josh's advice on using Nistune to check the voltages (which is a perfect method!) if you see anything out of wack voltage wise, THEN get the multimeter out and read the voltage directly at the sensor. If the two vary, then you're now looking for a wiring issue vs a sensor issue. So be aware, what the ECU sees, may not be what the sensor is actually saying too...
    • You very likely need to get it on a dyno and tune it. My assumption is, you've got an RB25DET tune in it, which has a different manifold, different injectors, and different cams as a minimum. What O2 sensor are you running?   When you say it runs extremely rich from idle all the way to redline, is this just free revving it you see that?
    • I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
    • I don't know any details, but I really wouldn't be surprised if they do it as a LHD only version, at least initially.
×
×
  • Create New...