Jump to content
SAU Community

Recommended Posts

I just bought a skyline(R33 series II) and am having the following problems. (Lucky its still under warrenty, so I'm taking it back to get it fixed) But just wanted to know if any else has experience this problem.

When I'm going slow at about 20 to 30Km/h and am about to take a corner, i sometimes put it in neutral before i enter the corner then when I exit the corner I put it into gear and drive off.

However, sometimes when i put it into neutral the engine just cuts off and dies.

So now I drive it with the car always in gear. so when i take a corner now, i put it in 2nd or 3rd gear and take the corner. However the same thing is happening and the engine cuts off.

It's not happening all the time. But for the last 2 days of driving, its happened about 5 to 6 times.

The idle is steady. This seems to only happen when i'm going at about slow at about 20km/h.

Any ideas/help would be great.

Link to comment
https://www.sau.com.au/forums/topic/152772-engine-dies/
Share on other sites

what kind of bov do you have on your car? if you've got an atmo bov then it would be causing this.

yeah. Its an after market BOV. blitz bov.

but does this mean that the bov is stuffed? or just crap and I should get a better one?

and thanks for the reply.

Link to comment
https://www.sau.com.au/forums/topic/152772-engine-dies/#findComment-2841424
Share on other sites

The venting bov's is a common problem with R33's with their sensitive air flow meters, Because the air isn't being plumbed back and the air flow meter cant sense any air coming back through when changing gears or gearing down it overfuels and stalls. Get the standard one or a plumb back one and make the air go back into the intake pipe or get a safc or another ecu (which is what mighthave been on prior to you buying the car). Go back to standard you cant go wrong if you dont have many mods like bigger turbo.

Link to comment
https://www.sau.com.au/forums/topic/152772-engine-dies/#findComment-2841534
Share on other sites

It could be the BOV but i would also make sure that it isnt a bad connection or dry solder joint with the AFM.

I had a similar problem when i had my GTR and when i changed down gears i had to keep on the revs sothe car wouldnt stall...

Was a problem with my AFM's... Might not be the same for you but dont rule it out.

Link to comment
https://www.sau.com.au/forums/topic/152772-engine-dies/#findComment-2841809
Share on other sites

It could be the BOV but i would also make sure that it isnt a bad connection or dry solder joint with the AFM.

I had a similar problem when i had my GTR and when i changed down gears i had to keep on the revs sothe car wouldnt stall...

Was a problem with my AFM's... Might not be the same for you but dont rule it out.

This is probably a stupid question. But what does AFM stand for?

Link to comment
https://www.sau.com.au/forums/topic/152772-engine-dies/#findComment-2841841
Share on other sites

maybe try tightening the spring on the bov so its harder and doesnt vent on low pressure.

either that or do the afm fix, if it doesnt do anything then grab a stock/plumback bov or get a tune-able ecu/piggyback computer.

Link to comment
https://www.sau.com.au/forums/topic/152772-engine-dies/#findComment-2842168
Share on other sites

I just bought a skyline(R33 series II) and am having the following problems. (Lucky its still under warrenty, so I'm taking it back to get it fixed) But just wanted to know if any else has experience this problem.

When I'm going slow at about 20 to 30Km/h and am about to take a corner, i sometimes put it in neutral before i enter the corner then when I exit the corner I put it into gear and drive off.

However, sometimes when i put it into neutral the engine just cuts off and dies.

So now I drive it with the car always in gear. so when i take a corner now, i put it in 2nd or 3rd gear and take the corner. However the same thing is happening and the engine cuts off.

It's not happening all the time. But for the last 2 days of driving, its happened about 5 to 6 times.

The idle is steady. This seems to only happen when i'm going at about slow at about 20km/h.

Any ideas/help would be great.

Why do you even put in neutral when you enter a coner anyway?

Link to comment
https://www.sau.com.au/forums/topic/152772-engine-dies/#findComment-2844192
Share on other sites

I had a stalling problem when I first got my car, same as yours, it would just die. We traced it back to an air leak that the dealer thought was in the exhaust before the cat. Turns out that the whole manifold on the engine block was not good and leaking. U should get a mechanic to go over your car with a fine tooth comb to make sure that nothing gets missed. It is worth the cost cause if something major is rooted it will cost a lot more than 30 mins of labour or a case of beer to fix :)

Welcome to the forums mate!

Link to comment
https://www.sau.com.au/forums/topic/152772-engine-dies/#findComment-2844244
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The average previous owner for these cars were basically S-chassis owners in the US. Teenagers or teenager-adjacent. I often tell people that neglect is easier to fix than something that was actively "repaired" by previous owners.
    • Update 3: Hi all It's been a while. Quite a lot of things happened in the meantime, among other things the car is (almost) back together and ready to be started again. Things that I fixed or changed: Full turbo removal, fitting back the OEM turbo oil hardlines. Had to do quite a bit of research and parts shopping to get every last piece that I need and make it work with the GT2860 turbos, but it does work and is not hard to do. Proves that the previous owner(s) just did not want to. While I was there I set the preload for the wastegates to 0,9bar to hopefully make it easier for the tuner to hit the 370hp I need for the legal inspections that will follow later on. Boost can always go up if necessary. Fitted a AN10 line from the catch can to the intake hose to make the catchcan and hopefully the cam covers a slight vacuum to have less restrictive oil returns from the head and not have mud build up as harshly in the lines and catch can. Removed the entire front interior just shy of the dashboard itself to clean up some of the absolutely horrendous wiring, (hopefully) fix the bumpy tacho and put in LED bulbs while I was there. Also put in bulbs where there was none before, like the airbag one. I also used that chance to remove the LED rpm gauge on the steering column, which was also wired in absolute horror show fashion. Moved the 4in1 Prosport gauge from sitting in front of the OEM oil pressure gauge to the center console vents, I used a 3D printed vent piece to hold that gauge there. The HKB steering wheel boss was likely on incorrectly as I sometimes noticed the indicator reset being uneven for left vs. right. In the meantime also installed an airbag delete resistor, as one should. Installed Cube Speed premium short shifter. Feels pretty nice, hope it'll work great too when I actually get to drive. Also put on a fancy Dragon Ball shift knob, cause why not. My buddy was kind enough to weld the rust hole in the back, it was basically rusted through in the lowermost corner of the passenger side trunk area where the wheel arch, trunk panel and rear quarter all meet. Obviously there is still a lot of crustiness in various areas but as long as it's not rusted out I'll just treat and isolate the corrosion and pretend it's not there. Also had to put down a new ground wire for the rear subframe as the original one was BARELY there. Probably a bit controversial depending on who you ask about this... but I ended up just covering the crack in the side of the engine block, the one above the oil feed, with JB Weld. I used a generous amount and roughed up the whole area with a Dremel before, so I hope this will hold the coolant where it should be for the foreseeable future. Did a cam cover gasket job as the half moons were a bit leaky, and there too one could see the people who worked on this car before me were absolute tools. The same half moons were probably used like 3 times without even cleaning the old RTV off. Dremeled out the inside of the flange where the turbine housing mates onto the exhaust manifolds so the diameter matches, as the OEM exhaust manifolds are even narrower than the turbine housings as we all know. Even if this doesn't do much, I had them out anyways, so can't harm. Ideally one would port-match both the turbo and the manifold to the gasket size but I really didn't feel up to disassembling the turbine housings. Wrapped turbo outlet dumps in heat wrap band. Will do the frontpipe again as well as now the oil leak which promted me to tear apart half the engine in the first place is hopefully fixed. Fitted an ATI super damper to get rid of the worn old harmonic balancer. Surely one of the easiest and most worth to do mods. But torquing that ARP bolt to spec was a bitch without being able to lock the flywheel. Did some minor adjustments in the ECU tables to change some things I didn't like, like the launch control that was ALWAYS active. Treated rusty spots and surface corrosion on places I could get to and on many spots under the car, not pretty or ideal but good enough for now. Removed the N1 rear spats and the carbon surrounding for the tailpipe to put them back on with new adhesive as the old one was lifting in many spots, not pretty. Took out the passenger rear lamp housing... what do you know. Amateur work screwed me again here as they were glued in hard and removing it took a lot of force, so I broke one of the housing bolts off. And when removing the adhesive from the chassis the paint came right off too. Thankfully all the damaged area won't be visible later, but whoever did the very limited bodywork on this car needs to have their limbs chopped off piece by piece.   Quite a list if I do say so myself, but a lot of time was spent just discovering new shit that is wrong with the car and finding a solution or parts to fix it. My last problem that I now have the headache of dealing with is that the exhaust studs on the turbo outlets are M10x1.25 threaded, but the previous owner already put on regular M10 nuts so the threads are... weird. I only found this out the hard way. So now I will just try if I can in any way fit the front pipe regardless, if not I'll have to redo the studs with the turbos installed. Lesson learned for the future: Redo ALL studs you put your hands on, especially if they are old and the previous owners were inept maniacs. Thanks for reading if you did, will update when the engine runs again. Hope nothing breaks or leaks and I can do a test drive.
    • No those pads are DBA too  but they have colors too. I look at the and imo the green "street" are the best.
    • I’m not sure what happened I told them about sonic tunes free OTS tune and the next the I know .. I was booted..   To funny 
×
×
  • Create New...