Jump to content
SAU Community

Recommended Posts

hey guy and girls i was just woundering if any one has put a set of 20's on a stagea?

i was just woundering because i used to have a 33 and when i put 20's on it i had some trouble with wheels rubbing on suspension top arm at the front. i had 35 profile tyres. we did get it to work. with some light modifying.

i could got around this problem by using 30 profile tyres but they just look shit on 20inch rims just looks like not enough tyre.

i was just posting up if anyone knows if 20's will fit as i live in a smaller town and if i order up rims they dont like sending em back if they dont fit

and most 20inch rims are usually 8.5inch wide i was woundering if anyone has run into trouble?

if its to much drama i'll just order 19's

hope someone has some imput

thanks in advance

chris

PS i wanna use standard suspension in car with king springs. i dont wanna really buy coil overs

as there is a stagea in town with 20's but im pretty sure he has coil overs

Link to comment
https://www.sau.com.au/forums/topic/152917-fitting-20s-on-a-stagea/
Share on other sites

you wont make em fit without shaving the top arm with 35 profile tyres. if you dont want that drama, go the 19s, they look huge anyway.

i got 20s on my r33 with 30 profile tyres, rides absolutely sh*thouse.

Edited by _8OO5TED_
yea mate thats the "modifycation" that i did on my skyline

had to take about over 1mm out

and yea 30 profile would be gay :devil:

why are 30 series tyres 'GAY"?

I have 35s atm and have had 40s, and 45s previously, and they all seemed to be fine....

Just cant imagine teh 30s being that bad!!

my two cents/questions!!

Peter

Edited by SEX-DR.

post-22927-1169737194.jpgin reply to ctjet and manwhores posts about them looking gay with 20's on

i thought they would too but there is one getting around town at the moment that looks quite nice i think

i attached a pic to show you

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I'm with you here. It's either loom has an issue, OR, injectors are not functioning properly. It could even be they're just constantly dribbling, hence the wet, but not firing.
    • Depending on how long the car sat it is very possible for injectors to be stuck open or closed, I'd get them cleaned and flow tested. Other than that, obviously when the loom changes and the car doesn't start any more....the loom is suspect so some tracing / comparing may be required
    • Harness is for a s1 Rb25det, and it is engine and lower harness.  the old harness had broken off plugs and was in very rough condition/exposed wires and splices etc. it is not able to be put back on the car, I could visually inspect to see if they had rewired any pins on the ecu plug. The fuel pump definitly isn’t turning off it’s an external pump and very loud you can hear it. Will look at the other harness tonight, am also going to pull the fuel rail and watch the injectors spray, will update here with what I find. Pretty sure at this point it has to be something to do with injectors because car will fire up on starting fluid and cas is clicking the Injectors. Fuel pressure is steady 43psi 
    • Check the injectors flow evenly, and are actually flowing what you and the ECU think they should be flowing. If it's starting up on starter fluid, you have a fuel issue. Is it possible under cranking your fuel pump is turning off?   The harness you replaced, is that the whole engine harness? Do yourself a test, and drop the old harness on and plug it into the Z32 ECU. It's possible they've wired things different. From memory S1 to S2 is different in RB25 and you may have a wrong loom
×
×
  • Create New...