Jump to content
SAU Community

Recommended Posts

Hi Guys,

Planning to get the hicas locked out on my car, from what i've been told seems likes theres two options to go for (short of removing the whole system).

Just wondering whats better to get, just one of those standard hicas lock bars that seem pretty easy to source and work for most cars, or the tomei hicas lock kit, with the electronic module and the shims.

any info would be much appreciated.

Cheers,

Dave.

Link to comment
https://www.sau.com.au/forums/topic/152920-r32-gtr-hicas-lock-question/
Share on other sites

The Tomei kit adds weight, but gets rid of hicas pretty effectively. Using the lockbar you can remove ~30kg of deadweight.

Warning light issue can be solved by cutting the sender wire on the hicas computer.

Lock bar is also the cheaper option I'm fairly sure.

http://www.skylinesaustralia.com/forums/in...showtopic=93183

Do that ^^^^^ , with the warning light i pulled the light out of the dash if u are unconfindent about cutting wires

ok but i'm a bit of a noob, don't exactly have the time or the facilities to do ti myself, who can i get to do it for me??

The Tomei kit adds weight, but gets rid of hicas pretty effectively. Using the lockbar you can remove ~30kg of deadweight.

Warning light issue can be solved by cutting the sender wire on the hicas computer.

Lock bar is also the cheaper option I'm fairly sure.

OMG! 30KG! I am doing the bar for sure!

personally I went the tomei kit for a couple of reasons.

1. hicas had not bothered me too much. the odd uneasy feeling from the rear was sometimes off putting, but I dont think it was slowing me down too much either on or off track.

2. with that in mind I wanted something easily reversible.

3. it's neat

4. it's cheap

5. it's easy to install

6. no dash warning

7. no heavy steering

8. no fear of busted PS pump

as far as I could see the advantages of a lock bar vs tomei kit were.

1. decent weight saving.

2. ummm that's it.

so after weighing that up, the tomei kit was for me. it works fine. but lock bar is a good solution too IF done well.

i ripped it all out, ill say now its not 30 kg, ill weight it one of these days

Spoke with Ant Scali before I did mine and from memory it was a 26Kg saving on his 32R

Ok, so where to get it done, and how much would I be looking at?

Depends on where you live, If it was on the West coast I could help a brother out but i'm guessing your on the east sieeed so ??

Price... a couple of hours for an experienced hand plus sorting out the power steering pump + the lock bar ..dont know if GTRgeoff is fabing them at the moment. Cheap considering the results.

6. no dash warning

7. no heavy steering

8. no fear of busted PS pump

I agree that the Tomei kit is an easier solution, but these 3 points are very easy to avoid when using a lockbar.

6. Cut the sender wire from the hicas computer. Green with white trace line in bottom left hand corner of the smaller plug.

7. Heavy steering is caused by people leaving solenoids plugged in. I had someone come to me complaining about heavy steering, unplugged the solenoid and the problem was gone.

8. PS pumps only get busted when people block the lines off. The rear stage of the pump is trying to pump fluid that has no where to go.

I wrote a DIY on it a while ago, and have done it on 3 cars without a single problem.

http://www.nissansilvia.com/forums/index.p...howtopic=185697

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • What are we supposed to be seeing in the photo of the steering angle sensor? The outer housing doesn't turn, right? All the action is on the inside. The real test here is whether or not your car has had the steering put back together by a butcher. When the steering is centred (and we're not caring about the wheel too much here, we're talking about the front wheels, parallel, facing front) then you should have an absolutely even number of turns from centre to left lock and centre to right lock. If there is any difference at all then perhaps the thing has been put back together wrongly, either the steering wheel put on one spline (or more!) off, and the alignment bodged to straighteb the wheel, or the opposite where something silly was done underneath and the wheel put back on crooked to compensate. Nut there isn't actually much evidence that you have such a problem anyway. It is something you can easily measure and test for to find out though. My money is still on the HICAS CU not driving the PS solenoid with the proper PWM signal required to lighten the load at lower speed. If it were me, I would be putting either a multimeter or oscilloscope onto the solenoid terminals and taking it for a drive, looking for the voltage to change. The PWM signal is 0v, 12V, 0V, 12v with ...obviously...modulated pulse width. You should see that as an average voltage somewhere between 0V and 12V, and it should vary with speed. An handheld oscilloscope would be the better tool for this, because they are definitely good enough but there's no telling if any cheap shit multimeter that people have lying around are good enough. You can also directly interfere with the solenoid. If you wire up a little voltage divider with variable resistor on it, and hook the PS solenoid direct to 12V through that, you can manually adjust the voltage to the solenoid and you should be able to make it go ligheter and heavier. If you cannot, then the problem is either the solenoid itself dead, or your description of the steering being "tight" (which I have just been assuming you mean "heavy") could be that you have a mechanical problem in the steering and there is heaps of resistance to movement.
    • Little update  I have shimmed the solenoid on the rack today following Keep it Reets video on YouTube. However my steering is still tight. I have this showing on Nisscan, my steering angle sensor was the closest to 0 degrees (I could get it to 0 degrees by small little tweaks, but the angle was way off centre? I can't figure this out for the life of me. I get no faults through Nisscan. 
    • The BES920 is like the Toyota Camrys of coffee machines. E61 group head is cool, however the time requirements for home use makes it less desirable. The Toyota Camry coffee machine runs twin boilers and also PID temp control, some say it produces coffees as good as an E61 group head machine.
    • And yes with a full tank it will hit limiter free revving or driving 6B6CDF6E-4094-426D-A9CB-6C553475FE36.mp4
    • One way of putting the fuel surge idea to rest, is that even when in neutral/clutch in or free revving it still has the same issue, it can’t even get to limiter (7800) so to me that says it can’t be g force, I’m not trying to argue I just want to find the f&$king issue 😡
×
×
  • Create New...