Jump to content
SAU Community

Ssr Vienna 19 X 9.5" & 10" Deep Dished Wheels With 285/30's

NXTIME
 Share

Recommended Posts

NXTIME Grand Master

NXTIME

Posted
Posted

Item: SSR Vienna 'Courage' 19 x 9.5" & 10" deep dished wheels with 285/30 Bridgestone tyres ($800 each new); fronts have +30 offset but come with new 15mm bolt-on spacers to make offset +15; rears are +11, O disk.

Unfortunately, these wheels won't fit my R32, but will suit R33/34 GTR's.

Location: Sydney/Wollongong

Condition: Excellent

Price: $3,300 ($8,000+ new)

Payment: Pick up or Direct deposit. Buyer to arrange and pay for postage

Contact: PM or post here.

Other: More pics can be provided. Other tyre sizes available. Lips have been machined to removed gutter marks.

post-4183-1169721265.jpg

post-4183-1169721286.jpg

post-4183-1169721307.jpg

humz Proficient

humz

Posted
Posted

lovely rims

just wondering if you would swap a set of Super advan racing version2 wheels 18x9.5 all round (some low gtr offset) with tyres for yours without tyres?????? mine are also black with a black dish, red writing in the centre cap, and gold nut over the top????

http://www.fizzautosports.com/rim/rim_advan_r2.html

NXTIME Grand Master

NXTIME

Posted
  • Author
Posted
Whats wrong with guard lipping?

is it both expensive and damaging to the car's paintwork?

Not if done properly/professionally. Cost is about $50/guard.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Latest Posts

    • MBS206
      Jacks that fit under GTR lips that can reach the subframe?

      By MBS206 · Posted

      You need one of those automated sprays that puffs a nice small every 15 minutes in their room. Except swap the nice smell for chloroform...
    • MBS206
      Vag Coil Diy loom wire guage selection

      By MBS206 · Posted

      Don't step down power supply size, maintain it the whole way. It's how I'd do it. OR, Id have one feed, with one joint that splits out to six smaller gauge wires that go to each coil. I wouldn't add joins like stepping from 12 to 16, at the first two coils, as if you try to continue that fashion, each joint will introduce a voltage drop. In theory, earths should be the same size as power feeds, however in this case the main power needs to be bigger due to the average size current. So the next question is, how much current do these coils actually need?
    • MBS206
      Steps to DIY sanding car back ready for respray....

      By MBS206 · Posted

      I think Murray is onto it. It's sounding like either it's a soft block, not long enough block, OR if you're chasing waves, you're going in the direction of the waves, instead of across them. Rotate your sanding pattern by 45 degrees is something to try. You said you're going in an X, so now instead, from the same perspective, do a "t" instead.   If you're not able to have the block sit on top of two high points, and not touch the low point between them, you'll never get it flat.
    • Manur33
      Vag Coil Diy loom wire guage selection

      By Manur33 · Posted

      Hi, i’m making Vag coil loom for rb25det, can anyone confirm the wire guage i’m using for power supply in diagram is enough for supply not too small for loom? For earth do i need to follow the same procedure or i can use only 16awg wire for all coil and their connecting wire following to the plug?
    • Murray_Calavera
      Steps to DIY sanding car back ready for respray....

      By Murray_Calavera · Posted

      Did you panel beat the dents or have you tried to repair this only using filler?  Is your sanding block soft/flexible and is following the shape of the panel rather then just knocking down the high points? 
×
×
  • Create New...