Jump to content
SAU Community

Recommended Posts

Has anyone installed 6" component speakers in a R34, i am currently doing my whole new system and decided to put the components in the back as there is no room up the front for all the parts, does anyone have pics of work they have done or had done?

Also nissan have made a damn good car except the fact that i haven't stopped swearing since i started this project cause nothing lines up with the stock system.

-----------------remember smoke tyres not drugs-----------------

Link to comment
https://www.sau.com.au/forums/topic/153481-r34-system/
Share on other sites

just took the whole rear parcel shelf out so could get to speakers then found that the plastic cover over speakers has srews holding them on which you can access through some holes through the boot below the shelf, would of been handy to be able to see them first up, the shelf just clips through to the boot and also under the overlap behind rear seats, also to get my clarions in had to drill out the existing holes to fit new configuration.

i mean really it's not that hard if ya think about it hoo hah ( except for all the swearing)

----------------remember smoke tyres not drugs--------------

Link to comment
https://www.sau.com.au/forums/topic/153481-r34-system/#findComment-2855693
Share on other sites

directly underneath the speakers in the boot there should be a lot of holes in the sheetmetal i'm not sure what ones but there should be four on each side that go th the screws, really hard to see that's why i pulled the whole parcel shelf out it's much easier, there should be two blue clips in the boot and three inside the car behind the rear headrest plus you have to take the 3 bolts out that are for the baby harness points to get the shelf out. hope that helps

Link to comment
https://www.sau.com.au/forums/topic/153481-r34-system/#findComment-2855770
Share on other sites

there are two bolts holding the bottom part of the seat, remove tht. Then just take out the bottom piece seat and the rear there are two bolts as well at both sides, undo those, then lift the back piece as it is hooked on to the frame behind..quite a hassle because they don't fold down :cheers:

Link to comment
https://www.sau.com.au/forums/topic/153481-r34-system/#findComment-2855971
Share on other sites

nice work r34-gtt not that hard once you get it off and see whats going on under there. have my speakers in as well and just fitted the components box and tweeters to the back shelf as well so i'll post pics when it's all back together.

-------------------remember smoke tyres not drugs---------------

Link to comment
https://www.sau.com.au/forums/topic/153481-r34-system/#findComment-2856781
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Went to a drift practice day at a local circuit (held on the reserve parking area behind the grandstand) for the first time in about 15 years. Some kei cars were drifting as well, a not so surprising Suzuki Carry truck, and two 1st gen Daihatsu Copens that were converted to rear wheel drive(!) using Daihatsu Boon X4 transfer case, prop shaft and rear diff, obviously omitting the front driveshafts. They looked really fun to slide. I heard that they cost "about half" as much as a Nissan Silvia etc to run.  On the track 'Tech M' a local BMW tuning garage had a customer track day. Mainly recent models but there was one E36 which looked ancient among all the current models. It was cool watching the drifting and then turning around and seeing random people thrashing their M3/4s  central-circuit-drift-practice-2025-05-18-long-yt.mp4
    • I prefer it with those wheels (sacrilege?) 😋 Here's a photo of a fully original one for reference. The price is $350K....
    • I would like to keep it around 15k but if I need more to make it reliable and not have to worry about the car breaking I can go more. It's my project car so I'm just trying g to figure out what needs to be in it i know basic things like turbo cams injectors I'm just unsure of the size and the specifics so I'm spending alot of time on Google and its mostly rb25 and rb26 not alot on neo
    • This. They would need some tricky maneouvering to keep the income out of the country (the US). Which isn't helpful if that's where you want the income to end up.
×
×
  • Create New...