Jump to content
SAU Community

Recommended Posts

1992 R32 Nissan Skyline GTS-t M-Spec

approx 213000km

Recently had its major service at 197,000km, in which the following items were replaced:

* Clutch Slave Cylinder

* Timing Belt (Gates Racing)

* Idler and Tensioner bearings

* Water Pump

* Fuel Lines

* Fuel Filter

* Cam Seals

* Crank Seals

* All Belts

* Coolant Flushed

* Gearbox Oil (Redline Lightweight Shockproof)

* Differential Oil (Motul Gear300)

Has a reconditioned radiator with new end tanks (reconditioned approx 6 months ago)

Just replaced the rear rack ends and the rear steering arm balljoints

Front tie rod ends were replaced just after major service.

The car is serviced (spark plugs, oil filter, oil) every 5000km

Religiously looked after by conservative/mechanically sympathetic owner (i.e. car gets driven like your grandparents are driving)

The car made 171.3 rwkw on only 11psi boost

Car has run a 1:03:39 on the Sportsman circuit at Queensland Raceway

Car has run a 1:03:78 on the Sprint circuit at Queensland Raceway

These times were recorded with very little race experience, and i feel there is a lot more potential in the car with a 'good' driver. The car was also only running around 155rwkw at this stage.

Car is registered until July 2007

Exterior Mods:

* Nissan S14a Rims with GoodYear Revspec RS-02 Tyres, in 205/55/16 (tyres approx 50% remaining)

and

* Nissan R32 GTS-t Rims with Bridgestone RE55s (SR Compound) Tyres, in 225/50/16 (approx 70% remaining)

* Rear Wing Removed, and Boot Welded Up/Resprayed

* R32 GTR or GTS-t Type M Sideskirts and Rear Pods

* R32 GTR Front Grille

* R32 GTR Aluminium Bonnet

Interior:

* Nismo Leather Gearknob

* New Leather Gearstick and Handbrake Boots

* R32 GTR Steering wheel

* R32 GTR Drivers Seat

* Autometer Boost Gauge

* Impakt's NissanDataScan Consult Interface

* GReddy Turbo Timer

ICE:

* Pioneer DEH-P4650MP Head Unit (With Remote Control)

* Blaupunkt 200w 6.5" Splits in the rear

Suspension & Braking:

* Kings 'Lows' Springs front and rear (Fitted 26/07/2005)

* Bilstein Shocks front and rear (as above)

* Flying Performance Front Strut Brace

* Generic Rear Strut Brace

* Whiteline 24mm Front and 22mm Rear, Blade Ajustable swaybars

* Whiteline Adjustable Front Camber Bushes (Fitted 26/07/2005)

* Whiteline Adjustable Front Castor Bushes (as above)

* Whiteline Adjustable Rear Camber Bushes (as above)

* Whiteline Subframe Lock and Align Kit (as above)

* Custom made Hicas Lock Bar

* Ferodo DS2500 brake pads front and rear (only a couple of months old - barely worn)

* DBA 4000 Slotted Rotors on the front

* Machined standard Rotors on the rear

* Motul RBF600 Brake Fluid

Engine:

* Flying Performance 3" Front/Dump Pipe Combo

* 3" High-Flow Cat

* 3" Kakimoto Catback Exhaust (extremely quiet)

* K&N Pod Filter

* Custom Heat Shield for Pod Filter

* Heavy Duty Clutch of Unknown Origin

* RB25 Turbo with RB20 Actuator (increases base boost)

* R34 GTT Sidemount Intercooler with Custom Piping

* GATES Racing strengthened Timing Belt

* D2 Fuel Pressure Regulator

* Walbro 255 Litre/Hour Fuel Pump

* GReddy Type S Plumbback BOV

* TurboTech Boost Controller set to 11psi

* Remapped ECU Chip mapped by DrDrift

There's probably a heap of things i've left out, but i can't think of any more at the moment...

if you have any questions, feel free to post them here, and i'll do my best to answer them for you! smile.gif

Here are some pictures of the car from 27.08.2006 (Still looks the same)

picture1.jpg

picture2.jpg

picture3.jpg

picture4.jpg

picture5.jpg

picture6.jpg

as you can see, the car is well looked after, and is probably one of the cleanest around...

and some of the dyno chart:

dyno001.jpg

dyno002.jpg

PRICE DROP! NOW $15200 ONO

Car is located in Brisbane

Link to comment
https://www.sau.com.au/forums/topic/154091-1992-r32-gts-t-type-m-modified-bne/
Share on other sites

You say:

Religiously looked after by conservative/mechanically sympathetic owner (i.e. car gets driven like your grandparents are driving)

Then you also go on to say:

Car has run a 1:03:39 on the Sportsman circuit at Queensland Raceway

Car has run a 1:03:78 on the Sprint circuit at Queensland Raceway

Discuss.

You say:

Religiously looked after by conservative/mechanically sympathetic owner (i.e. car gets driven like your grandparents are driving)

Then you also go on to say:

Car has run a 1:03:39 on the Sportsman circuit at Queensland Raceway

Car has run a 1:03:78 on the Sprint circuit at Queensland Raceway

Discuss.

Lol.. A track day doesn't = a dead car.. I'd be trusting this guy more than say (person B) e.g. some other guy who says he's never been to the track, has few if any service records and claims a bunch of things about how it's babied around. Because person B's car has most likely been thrashed on the street.

There's a difference.. This guy probably changes the oil before and after his track day (maybe) where as Person B thrashes his car most of the week and does bugger all to his car..

Just my 2 cents.

Lol.. A track day doesn't = a dead car.. I'd be trusting this guy more than say (person B) e.g. some other guy who says he's never been to the track, has few if any service records and claims a bunch of things about how it's babied around. Because person B's car has most likely been thrashed on the street.

There's a difference.. This guy probably changes the oil before and after his track day (maybe) where as Person B thrashes his car most of the week and does bugger all to his car..

Just my 2 cents.

exactly...

i don't thrash my car on the street, i usually bleed/change brake fluid, engine oil, oil filter, gearbox oil, diff oil, spark plugs etc after a track day, as well as doing an engine oil change beforehand (and i use good quality oils for all of these). When i drive the car on the street, i always warm it up before it sees boost (i.e. it doesn't see boost for the first 10 minutes of driving) and also warm it down for the last few minutes before i stop the car. At the track i warm the brakes, gearbox, diff up and down before and after use. Gearchanges are not hurried and i don't slam it into/crunch gears, as well as rev-matching on downchange (less stress on the gearbox)

There's a big difference between driving a car hard on the track and 'thrashing' the car on the street.

  • 2 weeks later...
  • 2 weeks later...
  • 3 weeks later...

It actually used to have a full GTR kit on it (front bar and spoiler), but with the old suspension, one point of the GTR front bar was 2mm too low, and i got defected for that.... so instead of spending $$$$ on the suspension at that time (i spent it later on though :)) i put on the front bar that you see in the photos to clear the defect.

  • 2 weeks later...

mate the kilometres travelled on this car are no more (actually, probably less) than 99% of R32's and R33's out there that claim to have '80,000km' or '100,000km' on the clock... only difference is, mine is showing the real reading, not like all the dodgey wound back crap out there...

and also, as said in the Ad, i am slightly negotiable, but i'm not going to let it go for something stupid like 11 or 12k like all the dreamers out there expect

mate the kilometres travelled on this car are no more (actually, probably less) than 99% of R32's and R33's out there that claim to have '80,000km' or '100,000km' on the clock... only difference is, mine is showing the real reading, not like all the dodgey wound back crap out there...

and also, as said in the Ad, i am slightly negotiable, but i'm not going to let it go for something stupid like 11 or 12k like all the dreamers out there expect

Couldn't agree with you more! Anyone who believes a 15 year old Skyline has 80000km is an idiot. Goodluck with the sale, looks clean and genuine :whistling:

Couldn't agree with you more! Anyone who believes a 15 year old Skyline has 80000km is an idiot. Goodluck with the sale, looks clean and genuine :closedeyes:

Agreed only the odd rare example would have k's close to 80k. Id feel happy to know what the car has actually travelled.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...