Jump to content
SAU Community

Recommended Posts

oh my god, stop clogging this useful thread up with crap. i was being facetious.

here's a few facts:

toyota and whipple are two different companies, and their blowers are COMPLETELY different.

currently i have an SC-14 on my RB30. i know what they are, and i know that supercharging has been covered because i did it.

whipple blowers are produced by lysholm AB industries in sweden. this is what is going onto my 25/30 hybrid engine. they are capable of massive power outputs with huge top-end airflow and no lag.

so stop posting useless stuff you obviously have no clue about. "toyota whipple blower" eh? where can i get one?

Stocky, you can't just not feed the vct from an external block source because it also feeds the front cam seal as well.

If you don't hook the vct gallery up the cam and seal will be rooted very quickly.

Also dont forget the front water gallery near the vct oil feed hole on the head surface needs some material added to it for a good seal. When you are getting the head reco, get them to weld the gallery up so it seals good.

And because you need that welded you might as well get the old vct gallery welded as well, rather then using a grub screw/plug.

:(

ah okay i was under the impression that it could be simply welded up and re-faced, obviously not! so i HAVE to feed oil into that gallery somehow then? i might as well use the VCT then, it will be just as easy. i think i can set up an RPM trigger to feed 12V to the solenoid when it needs it, shouldn't be too hard. or i can just leave it unplugged.

so you're 100% sure i have to feed oil up to that gallery? i am sure i have heard of a few people just blocking it off with a grub screw and leaving it, that's all.

The grub screw you've heard about blocks off the hole at the head/cylinder interface as there is no matching oil supply hole in the rb30 block as in the rb25. If you dont block it off your external oil feed will leak through this hole.

I played around with disconnecting the VCT solenoid on my stock cammed RB30DET and found that without it the bottom end was noticeably doughy. It is a relatively minor mod compared to implementing a blower system...

oh my god, stop clogging this useful thread up with crap. i was being facetious.

so stop posting useless stuff you obviously have no clue about.

I used to own a sc14 blower (not on an RB that's wrong) The bearings went in it coz I pushed it past 11psi.

sc14.jpg

Have you had the internals ceramic coated? coz going past 11psi with these things generate so much heat they melt the teflon coated internals.

i know that supercharging has been covered because i did it.

Please read the previous 93 pages, you have not mentioned about this but others have. It's worth reading everypage and saves the frustration of having to explain it all over again.

my target is 350-400 ponies at the wheels (300kw or so) and i simply don't need any more than that. from all my calcs, i am pretty sure i'll only need about 14-15 psi at the most to achieve this (not from a turbo) so i should be right with stock cams etc.

I know who you are and I know you mean well but 400rwhp is asking too much from that blower that's suited to a 2L.

Have a look at the link for a larger version of this blower. http://www.oguraclutch.co.jp/english/e_pro...sc/sc_siyou.htm

Sure, you can up the psi but doubt it's guna last you long.

PS: read the last 93 pages, you'll get a better idea then. :)

Keep the insults etc.. out this thread it's not needed here. :(

whipple blowers are produced by lysholm AB industries in sweden. this is what is going onto my 25/30 hybrid engine. they are capable of massive power outputs with huge top-end airflow and no lag.

PS: read 4 posts up and stop making a fool of yourself. telling me to read 93 pages of material and then, yourself, not even reading my posts before advising me on what to do is a little silly, no?

The grub screw you've heard about blocks off the hole at the head/cylinder interface as there is no matching oil supply hole in the rb30 block as in the rb25. If you dont block it off your external oil feed will leak through this hole.

yep i understand all of this no problems, just don't know how other people got away with not supplying oil at all to the forward cam seal and gallery there. because i have definately heard/seen pics of RB30DET's with the VCT oil feed welded up, and no external supply at all to the oil seal.

any ideas?

PS: read 4 posts up and stop making a fool of yourself. telling me to read 93 pages of material and then, yourself, not even reading my posts before advising me on what to do is a little silly, no?

You still don't quite understand. The blower used on the toyotas are whipple style blower. If you havent pulled both apart then trying doing that before replying.

If you cannot comprehend i'll show you the blowers in person.

Ps: You could put the motor into a better car tho.

they are in no way similar to a whipple blower at all, the whipple uses two counter-rotating screws which compress the air charge axially as they rotate. this is why it's called a twin-screw lysholm type blower.

the toyota blowers have two counter-rotating vanes which take a gulp of air and blow it out the other side. this is characteristic of a roots blower.

they are absolutely not the same in any way, shape or form. their only similarity is that they are both superchargers of some description.

whipple: compressor_cutaway.jpg

i don't have any inside shots of my SC-14 but perhaps you could post some up and understand just how different the two really are. apart from the casings looking vaguely similar, they are completely different. don't try and argue that a roots type blower is the same "style" as a twin screw because that's just stupid.

anyway back to the 25/30 thread here, is there any possibility of modifying the block to have another oil supply to the forward VCT gallery and using an RB25 head gasket? perhaps by drilling a hole into the nearest oil supply line and re-routing a portion of the flow to the new hole leading to the VCT gallery?

Perhaps we should move the supercharger posts to a new thread, this thread is really about RB30DET's. :)

PS, You don't get something for nothing, whipples need a lot of power to drive them (30 kw is not unusual) and they heat the inlet air charge up a lot (100 degrees C is also not unusual). This is a lot more power loss and heat generation than other designs. As I said, you don't get something for nothing, you have to pay the toll somewhere.

ah good to see someone took that flow chart i posted on board at least, yeah 40-50 horsepower to drive it at peak power, and they do generate heat, but then again i've seen some turbo flow charts with similar discharge temps. the gain is in the lack of lag, i'm just keen to try something new that's all. hate driving laggy cars on the street that's all.

but i digress, can anyone answer my questions above regarding the block modding or front cam oil seal?

ah good to see someone took that flow chart i posted on board at least, yeah 40-50 horsepower to drive it at peak power, and they do generate heat, but then again i've seen some turbo flow charts with similar discharge temps. the gain is in the lack of lag, i'm just keen to try something new that's all. hate driving laggy cars on the street that's all.

but i digress, can anyone answer my questions above regarding the block modding or front cam oil seal?

I have answered this question so many times in this thread. Test it yourself, block off the VVT oil feed (on the bottom of the cylinder head) with a finger. Then supply compressed air to the oil feed hole at the #1 camshaft bearing. You will find that the air circulates around the oil supply holes to the other camshaft bearings, ie; they are all joined up. You only need the EXTRA oil feed for the VVT becuase it needs a good supply of oil pressure. The #1 bearing oil supply is the bleed off, otherwise the oil pressure would be trapped there and the VVT wouldn't turn off when the solenoid is closed.:)

PS, a correctly sized tutbo should NOT go over 70 degrees C air inlet temp, but a correctly sized whipple will ALWAYS have to go over 100 degrees C to make its target power. As for no lag, it depends on your interpretion of LAG. The problem with a whipple (and all superchargers for that matter) is that they require increased rpm to supply increased air flow. So they have to be accelerated by the engine before the engine can accelerate the car. This means slowed response to throttle changes, both accelerate and decelerate. Propelry sized wastegates and BOV's have meant that turbochargers don't lag (sorry) behind as much as they used to.

You will find that the air circulates around the oil supply holes to the other camshaft bearings, ie; they are all joined up. You only need the EXTRA oil feed for the VVT becuase it needs a good supply of oil pressure. The #1 bearing oil supply is the bleed off, otherwise the oil pressure would be trapped there and the VVT wouldn't turn off when the solenoid is closed.

hmm two contradictory opinions, but it seems like you've done this a number of times. when i get the head next week hopefully i'll give it a go, come to my own conclusion.

and just a quickie, i have two options that i know of in terms of cam belt idlers/tensioners etc. do you suggest using the option of drilling a new idler stud hole up the top of the block or using two tensioners down the bottom near the crank pulley? the only advantage i can see of the former is less belt length on the slack side of the belt so perhaps less capability of belt whip/flop.

p.s. turbo vs supercharger, each to their own i guess. when it's running i'll let you know how it goes. hopefully the answer to that is "quickly".

hmm two contradictory opinions, but it seems like you've done this a number of times. when i get the head next week hopefully i'll give it a go, come to my own conclusion.  

and just a quickie, i have two options that i know of in terms of cam belt idlers/tensioners etc. do you suggest using the option of drilling a new idler stud hole up the top of the block or using two tensioners down the bottom near the crank pulley? the only advantage i can see of the former is less belt length on the slack side of the belt so perhaps less capability of belt whip/flop.

p.s. turbo vs supercharger, each to their own i guess. when it's running i'll let you know how it goes. hopefully the answer to that is "quickly".

I ALWAYS use the high mounted belt tensioner. In my opinion the low mounting position brings the belt too close together, the teeth are facing each other with sometimes less than 8 mm of separation. A little slack and you would have teeth to teeth contact at 6,000 rpm, and that does not make me feel very comfortable.

;)

I ALWAYS use the high mounted belt tensioner.  In my opinion the low mounting position brings the belt too close together, the teeth are facing each other with sometimes less than 8 mm of separation.   A little slack and you would have teeth to teeth contact at 6,000 rpm, and that does not make me feel very comfortable.

:rant:

Couldn't agree more, i looked at this in great detail when i built my motor, if you use the relocated tensioner the belt won't catch like it could do if you use the factory stud locations (which are way to close for this app) and with the relocated tensioner it also wraps the belt around the pullies better for more grip. :(

Gary,

don't stock rb26's let alone the os giken 3 litre kit use the lower tensioner and pulley setup? Meaning the belt has similar teeth clearance?

.

I ALWAYS use the high mounted belt tensioner.  In my opinion the low mounting position brings the belt too close together, the teeth are facing each other with sometimes less than 8 mm of separation.   A little slack and you would have teeth to teeth contact at 6,000 rpm, and that does not make me feel very comfortable.

:rant:

I ALWAYS use the high mounted belt tensioner.

no problem, it looks a lot better to me as well, for all the reasons you mentioned above.

two more questions then:

1) can you do it by eye with a hand drill?

2) how deep do you drill the hole to avoid going into the water gallery?

I made up a rig and clamped it to the block to help guide the drill bit completely square to the front block surface.

It must be absolutely right!

Then tapping it you have to constantly check with a 90deg square to make sure the thread is square with the front of the block surface.

I had an old block i practiced on first.

If its not absolutely correct the tensioner will sit on an angle andwear the belt and bearing, it may also not have enough grip if the trnsioner doesnt sit flush against the surface and may slip in use.

Someone may have a better idea but thats how i done it.

Because i had a spare block i was able to test the water gallery depth so to speak.

Its less than 9mm thats for sure, i had to cut the thread on the stud so it bottoms out.

I done it this way, but i really don't know if use would have trouble even if you went into the gallery and just used thread sealant on it, atleast that way the stud would have more thread/grip??

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
    • But first....while I was there, I also swapped across the centre console box for the other style where the AV inputs don't intrude into the (very limited !) space.  Part# was 96926-4GA0A, 284H3-4GA0B, 284H3-4GA0A. (I've already swapped the top 12v socket for a USB bulkhead in this pic, it fit the hole without modification:) Comparison of the 2: Basically to do the console you need to remove the DS and PS side console trim (they slide up and back, held in by clips only) Then remove the back half of the console top trim with the cupholders, pops up, all clips again but be careful at the front as it is pretty flimsy. Then slide the shifter boot down, remove the spring clip, loose it forever somewhere in the car the pull the shift knob off. Remove the tiny plastic piece on DS near "P" and use something thin and long (most screwdrivers won't fit) to push down the interlock and put the shifter down in D for space. There is one screw at the front, then the shifter surround and ashtray lift up. There are 3 or 4 plugs underneath and it is off. Next is the rear cover of the centre console; you need to open the console lid, pop off the trim covering the lid hinge and undo the 2rd screw from the driver's side (the rest all need to come out later so you can do them all now and remove the lid) Then the rear cover unclips (6 clips), start at the top with a trim tool pulling backwards. Once it is off there are 2 screws facing rearwards to remove (need a short phillips for these) and you are done with the rear of the console. There are 4 plugs at the A/V box to unclip Then there are 2 screws at the front of the console, and 2 clips (pull up and back) and the console will come out.
×
×
  • Create New...