Jump to content
SAU Community

R32 Gtr N1 Front Bar

JonesyGTR

By JonesyGTR,
in Exterior & Interior Styling

 Share

Recommended Posts

JonesyGTR Community Regular

JonesyGTR

Posted
Posted

Hi guys,

I am looking at getting a R32 GTR N1 frot bar. I currently have an aftermarket front bar on. Some one told me that the N1 slots require you to change the configuration, can anyone confirm this?

Has anyone done it previously? Please let me know of anything that will be relevant.

Ay pics would be great too. The bar I am looking at is designed for a GTR, not a gts-t.

Cheers,

Dan :P

Link to comment
https://www.sau.com.au/forums/topic/154254-r32-gtr-n1-front-bar/
Share on other sites
benm Grand Master

benm

Posted
Posted

I believe they are completely identical except for the 2 front slots. If you have an aftermarket fmic then you may need to trim the back of the slots shorter to fit the bar on but that's about it.

Note I could be entirely wrong!

Where are you getting the N1 bar? I need a new lip and want to put the N1 slots on my std bar, maybe it would be cheaper if I just bought an entire N1 bar instead.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Kapr
      "Cheap" bolt on turbo on RB25DET NEO

      By Kapr · Posted

      Ok guys thank you very much. GCG highflow it is then 🙂 
    • JC71
      98 R34GTT 4k engine stumble

      By JC71 · Posted

      forgot to mention that when it does this it does not kill the engine, but I have not kept the pedal down long enough to let it, as I see no reason to beat up on it as its got to be something simple, small and dumb causing this.  And as soon as I let off pedal, the engine returns to its normal super smooth operation and rpms re-stabilize quickly, once below 4k. 
    • JC71
      98 R34GTT 4k engine stumble

      By JC71 · Posted

      neither stumble or cut really seem to be an appropriate term....hard to explain its like a rev limiter but at 4k, but it violently shakes engine and entire vehicle as the rpms will not rise over 4k, even with slow acceleration. as soon as it hits 4k, it sounds like entire spark is lost entirely. plugs were 1.1 which I used as such, but later put in new plugs gapped down to .8 changed back after issue arose when I replaced the coils, still does it with either plug gap...damn and it was all running so good.
    • TurboTapin
      Why am I hitting a power wall with my stroked RB25?

      By TurboTapin · Posted

      Oh how times have changed! I actually lean it out relative to my water/methanol injector duty cycle. The methanol adds a lot of fueling and you can then lean it out even more due to reduced knock. 
    • Dose Pipe Sutututu
      Why am I hitting a power wall with my stroked RB25?

      By Dose Pipe Sutututu · Posted

      Yeah my thoughts are the same, a well thought out WMI setup, would be slightly ahead of just straight E85 and you're also chemically intercooling the charged air, dropping it even further. This is why you need to add so much more fuel as soon as you spray. I remember someone taking me through their set up before (Dennis, has a R33, lives around Cabramatta - no idea if he's still around on this forum). He would target AFR 10:1 on 98, then as WMI ramped on, AFR would lean back up to 11:1. Amazingly, he did this all through his PowerFC, a relay to cut power to his EBC solenoid if there was not enough line pressure on his WMI kit. And of course, if there wasn't any boost made above gate pressure, you wouldn't be accessing the load cells with heaps of timing for WMI. One downside to that rudimentary setup, once the WMI came on, the EBC would unleash the dragon, and of course all the timing. Tyres would fry lol.
×
×
  • Create New...