Jump to content
SAU Community

Recommended Posts

  • Replies 73
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

me FTL - *cough BULLSHIT cough*

coz im the king......and adz is the peasant, choo loose AHAHHHAAHAHA

yes ryan, you happen to be right on this one, i really do want to drive and show u up....but your degrading insults are really taking effect on my mental health......hahaha more bullshit, kansai better not smell like sex 2moro after leaving you and adz there by yourselves

parts used were

stagea lower control arms,hubs, rotors and calipers (although these will be swapped for R32 4 psiton etc)

so Stagea front stuff as in much no miss matching of parts

front would be as wide as if you put s14 lower control arms on so what 10-15mm wider on each side or something

the rear we had to use the stagea hubs and rotors on the ceffy rear craddle so its not any wider

ps Adz you owe me a tie rod end yours is gay

post-15018-1171863741.jpg

Edited by 1400r

^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^

HAHAHAHAHAHAHAHAHAHAHAHAHAHAHA. You mean he owes Terry.

Oh and I want those Rims.................

I might come out and keep u company wed ryan. I need to sort out this friggen problem with my engine. Its giving me the shits now.

No one likes the RB missing now

^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^

HAHAHAHHAHAHHAHAHHAHAHAHHAHAHAHHAHAHHAHAHAHAHHA

why were so many ha's required? lol

you have lots of company time ryan

g1 whenever

nicko whenever

brenton wednesday

me friday

we lub joo!

bringing a good tie rod on friday ryan - we install :P

Edited by Hella Flush
parts used were

stagea lower control arms,hubs, rotors and calipers (although these will be swapped for R32 4 psiton etc)

so Stagea front stuff as in much no miss matching of parts

front would be as wide as if you put s14 lower control arms on so what 10-15mm wider on each side or something

the rear we had to use the stagea hubs and rotors on the ceffy rear craddle so its not any wider

ps Adz you owe me a tie rod end yours is gay

So does that mean that stagea fronts will bolt on? Didn't you say it was the same as r33 ie need s14/15 front hubs? If its straight bolt on then im getting stagea setup!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • You just need to remove the compressor housing, not the entire turbo. I would not be drilling and tapping anything with the housing still on anyways. 
    • So, I put my boat on a boat. First of all, I'm going to come out and say it. Why is Tasmania not considered a holy goal, an apex that all road-legal modified cars go to, to experience? This place is an absolute wonderland of titanic proportions. If people are already getting club runs for once in a lifetime 30 person cruises to Tassy then I've never seemed to see it. It is like someone replaced the entire place with an idyllic wonderland for cars, and all of the people living there with paid actors who are kind, humble, and friendly. Dear god. After doing a lap of almost all of the place I've found that it's a great way to find out all of the little things that the car isn't doing quite right and a great way to figure it all out. All in all, I drove for 4 hours a day for a week and nothing broke. I didn't even need to open the engine bay. This is by all means a great success, but it has left me with a list of things to potentially address. I also now have a 3D printed wheel fitment tool which annoyingly hasn't got any threads in it to actually assemble it. I might be able to tape it together to check the sizing I actually want to use, but it'll likely involving pulling the shocks out to properly measure travel at least at the front, and probably raise the car while I'm at it, at least in the rear. I scraped on quite a few things and I'm not sure how else to go about it. I was taking anything with a bump at what felt like 89 degree angles. And address those 10 other tasks. And wash the car. God damn it is dirty. And somehow, the weather was perfect the entire time - And because I was on the top of Mt Wellington it turns out it was very much about to freeze up there. I did something I typically never do and took some photos up there in what must have been -10 and the foggy felt like suspended ice, rather than mere fog. If you own a car in Australia, you owe it to yourself to do it.
    • Damn that was hilarious, and a bit embarrassing for skylines in general 😂 vintage car life ey. That R33 really stomped. Pretty entertaining stuff
    • Hi, I have a r32 gtr transmission. Does any of you guys have an idea how much power it will hold with the billet center plate and stock gearset? At what power level and use did yours brake with or without billet plate? Thanks, Oystein Lovik
    • Saw this replica police car based on a Mitsubishi Starion XX parked next to a 'police box' (it's literally a box) in Hirohata, Himeji City in Hyogo prefecture the other day. It's owned by Morii-san who is a local Mitsubishi Starion enthusiast. According to a local radio station blog post, he always wanted to make a police car himself based on ones he saw in his favourite Manga comics.  As it's illegal to modify a car to look like a police car and drive on the road, Morii-san tried many times to get permission from Aboshi police station headquarters nearby. They refused initially by after they got tired of that they granted him permission. However, the car can only be displayed on private property and obviously can't be registered as long as the police livery is present. The car was completed at a cost of 1.5 million yen (US$ 10,000) in addition to the car cost. A location was chosen outside Hirohata Police box where the car can easily been seen from the street. Morii-san has two other Starion road cars, both widebody GSR-VRs.
×
×
  • Create New...