Jump to content
SAU Community

Recommended Posts

Ok so I need to change the brake pads.

Mitch says they are different to his so we are asking here on what to do...

Anyone done a change?

either the pads slide out when u remove the circlips holding them in or if they are the old style ones u need to unbolt the calipers (2 bolts, 17mm i think from memory) and pull caliper off and pull pads out and get a G-Clamp to press the piston back in enough for the thickness of the new pads so they can slip over the rotor, then install new pads :P

pretty easy task, should take about an hour for first timers :)

Edited by CruiseLiner

do you have normal brakes, gtr brakes or what?

98% of nissan brakes have two pins you poke out,Make sure that you dont leave the silver clip in the middle. you need that

and the pads come out of the top. then push the piston back into the caliper and drop your new pads in

should take all of 10 minutes a side even jacking and taking wheel off

Uber easy!!!

let us know if you have a problem though!

Edited by yokotas13

Yeah, i have r32 GTR all around and drilled rotors lol

i thought most nissans wer the pin type...hrm thats what i get for thinking!

Edited by yokotas13
Ok so I need to change the brake pads.

Mitch says they are different to his so we are asking here on what to do...

Anyone done a change?

You should only have to remove one of the bolts holding the caliper in, and it's best and easiest to remove the bottom one. You might want to slightly loosen the top bolt so you can "swing" the caliper up. Then, swing the caliper up and "over" the disk, pull the old pads, then compress the pistons back into the caliper (using a G-clamp and one of the old brake pads). After that, replace the old pads with the new ones - and don't forget the backing plates, that should stop your brakes from squealing. Once you've done that, lower the caliper back down over the new pads, and replace and tighten the bolt(s)...

Done!

(BTW, I just nutted this out from memory, so it's not a comprehensive DIY, but it's not a hard job either. There are quite a few cars where the process goes like this, and the technique is pretty much the same.)

put some r33 gtst or r32 gtr calipers and rotors on it, its definately needed if u do any spirited driving as the stock brakes are horrible and with automatic u cant use the gears to slow u down either :happy:

Stupid question time - are they a bolt on fit?

If so, it will be my next mod!!

yes they are :happy: i think only issue is the rotor dust shield needs a touch trimed off it to clear the bigger calipers. u need the r33 calipers and the r33 rotors to suit (297mm i think from memory). r32 gtr also fit as do the 33 brembos and 34 ones.

gotta love nissan and the number of interchangable parts between models :happy:

ok so can't find a place that stock the brake pads SK has recommended...

1398BP & 1144XL :happy:

Now what? :happy:

bendix advance db 1398 will fit on the front of s1 stagea [still a chance some came with diff calipers] best to drop 1 out and trace it or if your cashed up do what the guys say and swap the lot. just changed my pads and they still dont stop.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Seat of the pants assessment of the new intake: The car is way less "doughy" when hitting the loud pedal, especially off idle when stopped or in traffic, I did use a cheapo lazer thermal thingo to measure the temp around where the pod filter got its air, it was between 55 - 60°C, in saying this the car was shut off and not moving, so the OEM intake pipe was not supplying any fresh air to where the pod was when the car was at least moving A weird bonus was induction noise on the throttle in the cabin increased a bit,  I was worried that I was actually going to lose some of that induction noise I love so much, outside though, when I got the daughter to do a WOT drive by pass for me, the induction noise has increased alot when on the throttle, not quite ITB doort, but well up there I'm extremely happy with the results and have been exploring the country roads in the region  As for house mods: 1.New front fence is up and is awesome, it really upgraded how the joint looks from the street, and the added security is nice 2. Electricians have replace some interior lights, and with more lighting in the garage, a few new motion detecting lights out the front above the garage, front room, and at the front door, which I have already found heaps helpful coming and going, also now has fancy pants CCTV all round the house The only hold point for power though is the solar and batteries due to supply issues, although this will happen over the next few weeks 3. I have done a heap of landscaping out the front and I'm almost ready to do a new small retaining wall with some nice blocks to replace the brick and cemented in rocks around the raised garden beds cemented in river stone "was the fashion at the time" the house was built. I currently have a pallet of retaining wall blocks and 2 bulka bags of 20mm blue metal to replace the wood chip that is in the raised garden beds around the house 4. I now have 3 big raised garden beds for out the back to grow some vegetables, about 70cm high, 200cm long and 100cm wide 5. My 2 compost bins are already pretty full with brown, green and kitchen waste from the landscaping I'vedone so far, but they will probably take a few months to break down, so anything else that gets chopped, trimmed, and kitchen waste will just start filling the base of the raised garden beds to about 30cm before I start throwing 40cm of good compost, and stuff, for the vegetables to grow in, I'll need a few ton of compost and soil, but the local supplier can sent me bulka bags of the stuff Basically the logs, wood chips and a few strategically placed rocks for drainage, will give the beds some good organic materials down low to break down over time, and they will hold moisture during the warmer months to save the water in my big arse water tank if we don't get alot of rain So, all in all, the car and house mods are going well, and I'm really enjoying being retired, I sleep in too 0700 and slowly plod around inside until I feel like actually doing anything, and only work in the yard for as long as want, which has actually been alot over the last few weeks,  although when you look at it, it seems that not a huge amount of work has been done,  until I look at the before I started the work pics Happy days and good times indeed 
    • hahaha yeah. Plan is to get side skirts and probably just rear pods. But going to do them one-by-one. I've got a set that I really like from RHDJapen, but that one isn't shipped to AU. So need to find someone who can get it for me
    • Here's an idea, answer the questions I asked you as they are trying to work out WHY the LSD will be binding up in a straight line.
    • You haven't driven many modern cars then have you? Most of them have sfa steering feel with their stupid electric bullshit steering systems.
×
×
  • Create New...