Jump to content
SAU Community

How Do You Change The Brake Pads?

IMPORTD

By IMPORTD,
in Four Door Family & Wagoneers

 Share

Recommended Posts

CruiseLiner Mentor

CruiseLiner

Posted
Posted (edited)
Ok so I need to change the brake pads.

Mitch says they are different to his so we are asking here on what to do...

Anyone done a change?

either the pads slide out when u remove the circlips holding them in or if they are the old style ones u need to unbolt the calipers (2 bolts, 17mm i think from memory) and pull caliper off and pull pads out and get a G-Clamp to press the piston back in enough for the thickness of the new pads so they can slip over the rotor, then install new pads :P

pretty easy task, should take about an hour for first timers :)

Edited by CruiseLiner
yokotas13 Mentor

yokotas13

Posted
Posted (edited)

do you have normal brakes, gtr brakes or what?

98% of nissan brakes have two pins you poke out,Make sure that you dont leave the silver clip in the middle. you need that

and the pads come out of the top. then push the piston back into the caliper and drop your new pads in

should take all of 10 minutes a side even jacking and taking wheel off

Uber easy!!!

let us know if you have a problem though!

Edited by yokotas13
yokotas13 Mentor

yokotas13

Posted
Posted (edited)

Yeah, i have r32 GTR all around and drilled rotors lol

i thought most nissans wer the pin type...hrm thats what i get for thinking!

Edited by yokotas13
GoldZilla Grand Master

GoldZilla

Posted
Posted
Ok so I need to change the brake pads.

Mitch says they are different to his so we are asking here on what to do...

Anyone done a change?

You should only have to remove one of the bolts holding the caliper in, and it's best and easiest to remove the bottom one. You might want to slightly loosen the top bolt so you can "swing" the caliper up. Then, swing the caliper up and "over" the disk, pull the old pads, then compress the pistons back into the caliper (using a G-clamp and one of the old brake pads). After that, replace the old pads with the new ones - and don't forget the backing plates, that should stop your brakes from squealing. Once you've done that, lower the caliper back down over the new pads, and replace and tighten the bolt(s)...

Done!

(BTW, I just nutted this out from memory, so it's not a comprehensive DIY, but it's not a hard job either. There are quite a few cars where the process goes like this, and the technique is pretty much the same.)

Stinky Rooster Grand Master

Stinky Rooster

Posted
Posted
put some r33 gtst or r32 gtr calipers and rotors on it, its definately needed if u do any spirited driving as the stock brakes are horrible and with automatic u cant use the gears to slow u down either :happy:

Stupid question time - are they a bolt on fit?

If so, it will be my next mod!!

CruiseLiner Mentor

CruiseLiner

Posted
Posted

yes they are :happy: i think only issue is the rotor dust shield needs a touch trimed off it to clear the bigger calipers. u need the r33 calipers and the r33 rotors to suit (297mm i think from memory). r32 gtr also fit as do the 33 brembos and 34 ones.

gotta love nissan and the number of interchangable parts between models :happy:

leetom Proficient

leetom

Posted
Posted
ok so can't find a place that stock the brake pads SK has recommended...

1398BP & 1144XL :happy:

Now what? :happy:

bendix advance db 1398 will fit on the front of s1 stagea [still a chance some came with diff calipers] best to drop 1 out and trace it or if your cashed up do what the guys say and swap the lot. just changed my pads and they still dont stop.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      Duncan's V37.......race car?

      By MBS206 · Posted

      Even more fun, leave all the ADAS stuff plugged in, but in different locations, hopefully avoid any codes!   And honestly, all these new cars with their weird electronics. Pull all the electronics out Duncan, and just shove an aftermarket ECU and if needed a trans controller in, along with a PDM. Make it run basic but race car styled!
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • RP1421
      S15 Spec R

      By RP1421 · Posted

      As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • joshuaho96
      R32 GTS (RB20DE) Injectors Replacement

      By joshuaho96 · Posted

      I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
×
×
  • Create New...