Jump to content
SAU Community

Recommended Posts

Yes that’s right the famous 24 hour endurance racing motor 34N1 RB26DETT :D

This motor is still in the plastic and has never been installed, not a scratch on it. It took a long time to get this motor from NISMO and yes it is very rare.

I was going to put it into my 33gtr Vspec for circuit use, but I just don’t get the time of work to play with it.

I’m looking for $16500.00 cash but I’m in no rush to sell it !

Link to comment
https://www.sau.com.au/forums/topic/156021-r34-n1-motor-u24-brand-new/
Share on other sites

You'd probably want to be a little more specific about exactly which specification of N1 Motor it is and where it came from.

If its complete and brand spanking new then its not bad value.

Jash

  • 3 weeks later...

price drop $15,500ono for more info please give me a call

0415052743

the motor was inported form NISMO Factory through Bell Garage about a year ago.

still in plastic, red in coulur u24 r34N1 rb26dett

The motor is complete and brand spanking new still wraped in plastic

no inlet or exhaust manifolds

no turbos

no crank angle sensor

it has the new front diff, water pump turmostat and housing, oil pump ect and all those other little brackets fitted to the motor

its one flash looking donk with paper tag with numbers ect still attached

i don't get much time to get on line so for more info please call or message me

on 0415052743 cheers scotty

  • 2 weeks later...
  • 4 weeks later...

Here are some photo's as requested. Rolled plastic off for photo's then covered back up after photo's. Serious buyer's ring 0415 052743 for more info as I have limited access to the WWW.

post-16202-1176781279.jpg

post-16202-1176781180.jpg

post-16202-1176781294.jpg

post-16202-1176781312.jpg

post-16202-1176781329.jpg

post-16202-1176781342.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
    • Yes sir am asking is there possible way from aem tuner from wiring pins 
    • Have you checked cam to crank timing and confirmed balancer marks are correct?
×
×
  • Create New...