Jump to content
SAU Community

Recommended Posts

hi my am is to have a nice street car with decent power hears what Ive done so far.

SPECS AND MODS TO DATE:

ENG MODS:

K&N pod filter intake set up

cold air intake

custom air box

hight tech exctractors

2.25 exhaust with muffler and twin crome tip

nistune ecu

custom crow cam

adj cam gear

oil cooler

sound system

Sony head unit

clarion 6.5"splits front

clarion 6 x 9" rear

2 x clarion v-net subs

Alpine 250RMS mono block

alpine 4 x 40wrms 4ch amp

6.5" clarion speakers

clarion 2ch amp

RIMS, SUSPENSION

auscar burnouts 17x7 rims

with 225/45/ r17 Yokohama a drive r1 (shit tyre do not use)

king springs low 3.2kg/mm front 2.9kg/mm rear

kyb shcoks

r33 gtst calipers with dba 4000 sloted disc front

race brakes rb74 pads front

dba sloted disc rear

frodo exel pads rear

k-mac adj camber caster top hats

white line strut brace

white line 21mm rear sway bar

and a silo LSD

single pce tail shaft

3rds adj caster rods

cusco brake master cylender stoper

interior.

custom door trims

silo seats

ti steering wheel

painted dash anodised blue and mertalic silver

5 gages

trip computer

silo sun visers

exterior

painted front and rear bumbers

silo spoiler

cut the front bar (ref pic for work done)

clear indecator lenses

just jap front lip

custom side skirts

custom rear bumber

post-32868-1172367892.jpg

post-32868-1176450411.jpg

post-32868-1176450874.jpg

post-32868-1188634787_thumb.jpg

post-32868-1188635335_thumb.jpg

post-32868-1188635720_thumb.jpg

post-32868-1188636245_thumb.jpg

post-32868-1188636445_thumb.jpg

post-32868-1188636602_thumb.jpg

post-32868-1188636730_thumb.jpg

post-32868-1188636862_thumb.jpg

post-32868-1188636991_thumb.jpg

post-32868-1188637171_thumb.jpg

Edited by redliningr31 skyline
Link to comment
https://www.sau.com.au/forums/topic/157932-my-car/
Share on other sites

  • 2 weeks later...

up date guys.

looking at doing a R33gtst brake up grade to the front and getting some bucket seats got all gauges in and working.

drift ignight air fuel ratio

drift ignight water temp

drfit ignight volts

drfit neo oil temp

drfit neo oil pressure

cost $450

post-32868-1173948957.jpg

post-32868-1173949426.jpg

Link to comment
https://www.sau.com.au/forums/topic/157932-my-car/#findComment-2981932
Share on other sites

up date guys.

looking at doing a R33gtst brake up grade to the front and getting some bucket seats got all gauges in and working.

drift ignight air fuel ratio

drift ignight water temp

drfit ignight volts

drfit neo oil temp

drfit neo oil pressure

cost $450

nice tape :)

Link to comment
https://www.sau.com.au/forums/topic/157932-my-car/#findComment-2999471
Share on other sites

  • 3 weeks later...
  • 3 months later...

hi guys hears an up date.

just fitted r33 gtst front brakes and adj caster/camber top hats to the 31.

whats i used:

r33 gtst front calipers.

rb74 pads

dba 4000 sloted discs

cost: $600

k-mac adj camber/caster top hats

Cost: $400

new bumb stops

cost: $60

motul 5.1 brake fluid:

cost $30

redrill disc to 4x114.3

cost: $140

20mm spacers x 2

cost: $150

alimenght

cost: $45

misc

Cost: $75

total: $1500

the new set up is pretty good for handerling with avg of -1/5' camber and +4.5' catser.

and the wider track. the car is now more stable and has less roll and more predicterble in a drift

Link to comment
https://www.sau.com.au/forums/topic/157932-my-car/#findComment-3281849
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The wiring diagram for the R33 RB25 is freely available, and is essentially the same same as most other RBs (just with differences as to which pin # does which job). To get the ECU to power up, you just need to provide power to the ECCS relay, and have the other power feeds that come in from the top left of the wiring diagram (wrt the ECU) that give perma power to the fuel pump relay, the ECU itself, etc etc, all connected. When you put power on all these it will just come to life. It's pretty clear from the diagram what needs to happen. Just follow the lines from the 12V + supply stuff in the top left over towards the ECU. I've even posted snips of such diagrams (not for vanilla 25, I think for Neo and 26) to various threads here in the last few months, talking about what it takes to get the fuel pump and FPCM up and going. Search these up and they will help get you started on doing the same with the vanilla 25 diagram. Hell, for all I know, I've done the same with that one in years past and have forgotten.
    • Yep...so unless someone posts up the answer you will need to probe from the ECU connector to the dash plug with a multi meter in continuity mode to trace the wires.  Note the ECU has multiple - and + (and across different key settings - Battery, IGN and Start) and most likely the power is fed from the connector(s) that is normally near the left hand headlight.
    • Thanks Duncan, I am actually just trying to get the Rb turning and running with the RB25DET S2 original loom itself  I am just trying to get it going outside the body and not thinking about the S15 or trying to match anything to the S15 loom at all I am only trying to see if anyone has done this and what pin they found to be the ignition trigger and ECU+/- on the dash connector, that's about it. Thanks  
    • Hi Guys, Does anyone know any aftermarket part numbers for a starter motor to suit the VQ25DET? I can find lots of alternative part number for the VQ35DE, which I assume would fit, but there is a lot of conflicting information out there. Thanks..
    • I don't understand how this hasn't boiled down to - Upgrade the turbo when you have everything required. ECU, injectors, fuel pump, turbo, etc. Do it all at once.  If you don't have everything required, just enjoy the car as it is and keep saving up your pennies. 
×
×
  • Create New...