Jump to content
SAU Community

Sold

BWA

By BWA,
in For Sale (Private Whole cars only)

 Share

Recommended Posts

BWA Mentor

BWA

Posted
Posted

Reason for selling is that I'm only using the car once a week and don't really need it anymore. Rego until November 2007.

Car is completely stock and has never been modified, it would be extremely hard to find a 32 that has never been touched. There is zero police attention so you don't have to worry about getting pulled over all the time or getting defected. If you are looking for something to modify from scratch this is perfect.

In great condition. Has already had all drive belts (incl. cam belt) replaced with a new high flow fuel pump installed recently. Never had any major issues.

Has a 2 way pager alarm with immobiliser and keyless entry. The alarm also has a built in turbo timer.

Manual

Exeddy Heavy Duty Clutch (less than 10,000km's old)

New High flow fuel pump (less than 5,000km's old)

Electric sunroof

15% tint

16" Sparco rims

Type M Bodykit

First Australian Owner

115,000 km

Oil and oil filter religiously changed every 5,000km's

Price: $12500 ono

CRW_1784__800web.jpg

CRW_1636.jpg

In HPI:

CRW_2418_800web.jpg

Contact:

Amanda 0413120586 or email [email protected] or even just PM me

Link to comment
https://www.sau.com.au/forums/topic/157934-sold/
Share on other sites
Guest
This topic is now closed to further replies.
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • luke gtr
      Did tie rods. Steering now not "springing" back.

      By luke gtr · Posted

      Good to hear. Hopefully you're happy enough not to notice when driving and just enjoy yourself.
    • luke gtr
      Returning after a long time!

      By luke gtr · Posted

      I mean, most of us just love cars. Doesnt necessarily have to be a skyline.
    • luke gtr
      Returning after a long time!

      By luke gtr · Posted

      Did you pick up a manual cluster to remove the position indicator?  (Pretty sure the 34 has the gear position in the cluster, but it's been a while)
    • 33GTRV
      Rb26 iron block limit

      By 33GTRV · Posted

      Here is a recipe. Sonic blocks till you get one that has a good enough bore. Get a torque plate and block brace, use your choice of fasteners (arp ect) bolt the thing together empty, half fill it and let it cure. Release it when it has, go to a REPUTABLE RB Builder and get the thing line bored/honed and cylinder honed to size, then wash. Once its all clean and dandy, wash and blow it out again. Then again.  Assemble said engine to your desired clearances with oil control mods, gasket to suit desired CR/Squish ect. Attach your extended sump with proper trap door oil baffles and head drain plumbed to sump with a SUMP BREATHER SYSTEM. Build your front diff with a decent LSD, rebuild your transfer case with a few extra plates, more than likely replace your tailshaft centre bearing and tighten up the rear diff. Tune to minimise excessive midrange cylinder pressure (timing unless you like to split bores and rebuild engines) Enjoy your engine, but hate the fact you are now destroying engine mounts, gearboxes, gearbox mounts, diff output flanges and driveshafts, diff mounts, tailshafts and front CV's.   Disclaimer.... Ive never done any of the aforementioned stuff.......
    • GTSBoy
      R32 GTS (RB20DE) Injectors Replacement

      By GTSBoy · Posted

      440s will support well over 400HP on petrol, which is a decent place to be for an RB20. 230+rwkW. Will be a safer bet for idle/low load. 550s would be nice for the extra headroom. I've made the same decision with mine (Neo25). 1000s are probably too big for the Nistuned ECU, so I have some smaller ones.
×
×
  • Create New...