Jump to content
SAU Community

Recommended Posts

Time has come to sell the old girl and start a new project, its no autosalon winner, but definitely looks the part, and for it slides surprisingly well!!!

med_gallery_370_4520_64571.jpg

med_gallery_370_4506_717708.jpg

$13500 ono - see below for further information re. swaps etc.

Mechanical:

Silver-Top RB20DET

Boost Controller (12psi)

Hybrid FMIC & custom piping

RB20 Manual Gearbox

Walbro Fuel Pump

Highflowed Fuel Injectors

3" Exhaust & Dump Pipe

Heavy Duty Clutch - not a button but grabs well at any revs!

Suspension & Wheels:

Front YZ Sports Coilovers

Rear Pedders Springs and Struts

18" Mako Alloy Wheels - as per rear on side on photo

Bolt on 25mm spacers fitted since photos taken

Extra-Lock steering spacers

Front Strut Brace

Ratchet Handbrake Conversion

New Clutch Master & Slave Cylinders

Exterior:

Monkey Warehouse Bodykit

Custom Tinted PPG Devil Yellow

PPG Black Metallic with coarse gold glitter bonnet boot and roof

Black Tint

Interior:

R32 Skyline Front Seats

Autometer Boost Gauge

DVD Player

6" MTX Thunder speakers

Autotechnica Sports Steering Wheel

Car is in Brisbane. will freight interstate

Basically need to clear a debt of about 4k - so will consider trade with cash component my way

Link to comment
https://www.sau.com.au/forums/topic/158115-yellow-cefiro-for-sale/
Share on other sites

Guest
This topic is now closed to further replies.


  • Similar Content

  • Latest Posts

    • Ah! I actually managed to snag a lightly used set.... that aren't so suitable for me right now. They don't work on a GTT without some cutting or creative heat moulding. I thought about reselling them myself cause I didn't want to murder them, but it looks like I'm probably going to attempt to murder them/melt them because I may as well. @GTSBoy @PranK can somebody close this thread?
    • Hey mate,  I have a set, one is slightly damaged but wont be noticable once installed.  Shoot me a message if your still after them 
    • I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
    • You have a knack for photography my friend. It makes the 86 look like a complete bucket. The 34 went with you to Europe and back. It's special. (we all feel the same about our 'shitboxes' that every bystander seems to absolutely love)
×
×
  • Create New...