Jump to content
SAU Community

Recommended Posts

hey all, ive currently got both the turbo and exhaust manifold heat shields off of my rb20 and i thought i might as well paint them as they're definitely looking worse for wear. obviously id need to get very heat resistant paint but im curious on how i'd go about doing it. would i need to sand and/or prime the metal before painting? probably gonna go for a matte grey or silver look, adding a bit of bling to my engine bay :rofl:

also, would the rocker covers require special heat resistant paint or are most paints fine for those temperatures?

cheers all!

prosman

Link to comment
https://www.sau.com.au/forums/topic/158527-painting-heat-shields/
Share on other sites

hey all, ive currently got both the turbo and exhaust manifold heat shields off of my rb20 and i thought i might as well paint them as they're definitely looking worse for wear. obviously id need to get very heat resistant paint but im curious on how i'd go about doing it. would i need to sand and/or prime the metal before painting? probably gonna go for a matte grey or silver look, adding a bit of bling to my engine bay :)

also, would the rocker covers require special heat resistant paint or are most paints fine for those temperatures?

cheers all!

prosman

your best off going heat proof paint on any part of the engine bay.. u dont have to prime the metal but if u do then u wil need less coats to get the final colour u want.

Yeah, prep is the most important part, you should always rub something before you paint it, no matter what it is.

A green scotchbrite pad will do the job.

Then clean with a wax&grease remover (or just some metho will do ok). Wipe it on with 1 rag & off with another.

If they are bare metal, you will need to prime them. I havn't looked in the spray can section for a while, but if you can get a heat proof epoxy etch primer, use that, if not, then just normal epoxy etch. You will only need a thin coat of this, the thicker it is the easier it will chip off, so don't go overboard. Wait for it to tack then go the colour.

Heat proof enamel will be fine. Do a few thin even coats, wait till it has tacked off between coats, don't try to paint it in 1 go! Enamel over spray can travel a bit, so spray out in the backyard away from stuff, & they dont like being sprayed when its too humid or cold, so wait for a nice sunny day.

With spray cans, try to stick with the same brand for everything, that way you won't have any problems with different types of paint reacting with each other.

Normal spray cans should be ok for ya rockers, but if you want them to be the same colour as the shields just use the same can. If you want a gloss finish on them, its a good idea to use a couple coats of clear too.

Edited by frogman

use a high-temp paint

most of them don't need a primer (read the side of the can), and surely ifyou used a primer it would have to be a special high-temp primer anyway? makign it twice as expensive

just clean it properly first

i'd suggest going black on heat shields, so that even if the paint does begin to discolour you won't even notice! i paintedmy turbo heat shield red once with high temp paint and half of it turned black (burnt i assume), then i rubbed it back and painted it black before i sold it off

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
    • I don't know any details, but I really wouldn't be surprised if they do it as a LHD only version, at least initially.
    • Thanks for the replies everyone. Definitely a coolant push. Oil catch can is empty and always has been. As the engine is out now I'll be having a good look over things. I do have some detonation on the piston tops from a trigger issue back about 5 years ago. I felt it and shut off then bought a new ecu and changed the trigger. Never been an issue since. It never hurt the power, its made almost 80hp more since that incident but I will pull the bearing caps to take a look. If the bearings are damaged I will do a bottom end refresh. Head is being re conditioned at the moment and the block will be cleaned and checked to ensure it's flat. I'll go with a kameari gasket and see how it ends up. The other thing I'm not super keen on is the cylinder colours. I suspect this is from the inlet manifold. The plan will be to put it back together, retune and then stick a plazmaman billet inlet on it and retune. I'm happy with the power, if it makes a little more, then great, but I would rather just make everything more efficient at this stage.
    • Maybe they'll look to do a bunch of presales to help inject some cash fast for their financial issues...
    • Does it also misfire equally when revving?   Josh is very correct in what you should do. The coilpack harness wiring loom itself is a known problem due to its age and the number of heat cycles it has gone through. Throwing parts at a vehicle to diagnose the issue isn't a smart or good way to do it. Secondly, you may have a bad coil pack, you pop replacements in, they fix that issue, but messing with the harness breaks it, so the issue persists. So now you think "well it wasn't the coil packs" and have to continue chasing your tail, potentially swapping back in your shit coil packs and returning the good ones (yes, I've seen people do this because 'it wasn't the problem' and they want to save money). And suddenly, you've got two issues with the same symptoms...   Diagnose, don't use the spare parts shotgun.
×
×
  • Create New...