Jump to content
SAU Community

Recommended Posts

post-16789-1172968841.jpg

ok rims available any time now come get them i want 1300 1200 for them

will take 990 950 without tyres!!

will take 900 without tyres, tyres sold now. offers welcome

SOLD

ANYONE WANTS JUST RUBBERS PM AS WELL

post-16789-1172969412.jpgpost-16789-1172969434.jpgpost-16789-1172969455.jpgpost-16789-1172968812.jpg

and pics on the car:

post-16789-1172968841.jpgpost-16789-1172969348.jpgpost-16789-1172969382.jpg

Edited by HiOctane
Link to comment
https://www.sau.com.au/forums/topic/158572-r33-gtr-rims-wheels/
Share on other sites

  • 3 weeks later...

any chance you would you be interested in swaping for another set of R33 GTR wheels?

ive got a set that im trying to sell that have been fully polished on the face, so they look like chrome wheels.

ive been wanting to get a set so that i could get them powdercoated. but i dont want to do it to mine because they have been fully polished

adrian

Edited by Sticky

BUMP still FS had like 10 people interested but all evaporate for unknown reasons!! first to offer 1100 can have them, will send if required for additional cost,

Edited by HiOctane
BUMP still FS had like 10 people interested but all evaporate for unknown reasons!! first to offer 1100 can have them, please dont offer under 1100, will send if required for additional cost,

The problem is mate that the condition is very poor and that is going to put your average joe buyer off because they have to stuff around with rim repairs etc. If you want them gone in a hurry in that condition you might want to revise the price.

I'm sure eventually you can sell them but as far as unknown reasons go - i think the reasons are quite clear.

the condition doesnt look poor to me, they have some slight gutter marking around the edges but the spokes arent scratched.

they are almost as good as my R33 GTR wheels

the price is very good considering condition, the only reason it wouldnt be is if they were buckled

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeah I've had too many issues with knock off's on the BMW's. I don't want to do a job twice or more because the parts are shit.
    • I read this and thought "ah! I will do this scissor jack on the tow point thing!" I just use my floor/low profile/costco jack and lift the car up by the tow hook itself, then slide jack stands under. Never thought about using scissor into floor jack combo :p
    • Well, my new WMI system took much longer to finalize. I actually missed my dyno appointment last Friday and lost my 150$ deposit. I'll be going back in the next week or two.  To sum it up. I only kept the AEM tank from my old setup. I replaced the AEM pump with a higher flow/pressure ProMeth 30GPH pump. I also swapped over to a 6AN low pressure feed line to the pump from the tank. There's also a pressure switch you cannot see on the pump high pressure line.    This is feeding 6x 200CC direct port nozzles and 1x 500CC Pre Throttle body nozzle. All fittings are Swagelok, because well why not. I also have a 300PSI pressure sensor up front.    I now have my Haltech ECU controlling everything. I start my pump with a basic relay at 5PSI and deadhead it. I then PWM a 3000CC methanol Injector to control flow starting around 10psi. The pressure switch in the trunk, along with my tank level are safeties before I ever get to 10PSI, and then I use my pressure sensor upfront as a secondary safety to cut the WMI and corrections in case the injector blocks or a line ruptures.  Wish me luck on the dyno!    
    • So, I'm back with bad news. There's no jack long enough on this planet that will reach the front subframe. If by some chance there is, it would weigh 200lb's.  I purchased a long reach jack... The damn thing weighted 120lb's and was massive. Didn't even come close, was still short at least a foot. It was a pain, but I brought it back. Next I decided HA! No problem, I'll get an Extra long reach jack. Well, I couldn't lift the box... It must have weighed 160LB's and luckily there was an open box in store. I took measurement and was still nowhere close.  Sadly I've lost hope and have accepted defeat. 
    • Thanks for that tip, niZmO_Man. I think the battery is OK. It's quite a new one, but I'll check. Last time I needed a new battery, everything electronic was fine, except that there wasn't enough current to turn over the starter. I decided to order one of the partial AV system translation CDs from Car Audio Workshop in NZ. That might have some effect, or help me diagnose the date problem. 🤞
×
×
  • Create New...