Jump to content
SAU Community

Recommended Posts

Thanks to all who have approached me for having your ecu's remapped. I am now going to be backlogged for over a month >_< I may have spread my time a bit thin. so I will not be able to do any more remaps for the next month. Thanks guys for your support

  • 4 weeks later...

Hey all,

I just wanted to tell you about my great experiences with my CEF11E Tune, i origionally spoke to him about injectors and resistor packs for my rb20 and we got talking about tuning...

cut a long story short he offered to tune my car for me, this was great, saved me time, money and the tune is SPOT ON!

Nic has also been a great help to me in general and my car is now a rocket..... 230rwkw rocket!

Pretty talented if you ask me to tune a car without even seeing it! you act guys will have a better experience actually being able to see his face to face!

Ill have my dyno sheet posted soon

thanks

Ed

  • 1 year later...
would you do ar33 if it has a microtech lt12

CEF11E moved to Melbourne :P

I think we should kick his butt back here

If enough of us were able to get together, we could probably talk him into a weekend back in Canberra to visit the outlaws and tune ECU's LOL

To be honest I'm pretty sure he only has the software to do 32's, need some other stuff to burn r33 ecu's and it aint exactly as easy. Best to give him a pm, overall I'm happy with mine but I need a retune due to a boost leak when I was getting it done.

been reading into my ecu a bit and it sounds like the microtechs are more suited to drag so dont tune well for cruise, the SAU member then went on to say you can see a microtech car becasue theres carbon on the rear bar, true with my girl, really wanna get the tune done properly so i dont run rich and dirty my rear bar, any other options for a tune near campbell

cheers

alex

you can see a microtech car becasue theres carbon on the rear bar, true with my girl, really wanna get the tune done properly so i dont run rich and dirty my rear bar, any other options for a tune near campbell

cheers

alex

True that Alex. Mines the same. Just got to save up the 750+ for a Mitchell Tune or a 850 to 1k for a Fyshwick tune. But there are a few more options up here in Syd town. I can't wait to get it running well and "unleash the power of the primal warrior" (Lano and Woodly anyone) :)

Edited by Cpt. Rock

ay mate, thats a shit load of money, i have just got mine, so i have been fixing up some miss treatment from the previous owner, grrrr. so cant afford that at the moment, but car get up here on saturday so i am happy, have to start comming to the friday from next week onwards

alex

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...