Jump to content
SAU Community

Recommended Posts

http://www.bom.gov.au/cgi-bin/wrap_fwo.pl?IDQ20038.html

Just in registered at BOM

Be aware of them, just the quick heads up guys

Registed at 6:20pm Just thought id post it up in the case those who may be in the path

Cheers

A

Link to comment
https://www.sau.com.au/forums/topic/159655-severe-thunderstorms-se-qld/
Share on other sites

  • Replies 86
  • Created
  • Last Reply

Top Posters In This Topic

pretty light show happening around here atm. (Amberley) Sure hope it has some wet stuff in it as well.

see if you can get some pics.....

if you have a real (SLR) camera, just open the shutter til the light show finishes and then that hsould be an award winning photo :)

sik.. heading straight for the dams.... although looks like it will be a quick inny and outty which probably won't do much, other than smash stuff..

Its below the catcment area but :) needs to fall half way between Toowoomba and Kingaroy for the head of the river and largest catchment area :)

You mexicans are lucky as, we've only had one decent storm up here so far this year.

All we get is loads and loads of rain...

*sigh*

but seriously, if anyone can get some storm photos you should post them up so we can all have a captain cook.

You mexicans are lucky as, we've only had one decent storm up here so far this year.

All we get is loads and loads of rain...

*sigh*

but seriously, if anyone can get some storm photos you should post them up so we can all have a captain cook.

it looked like PD and mossman got pissed on today.....

well out at the beaches we only had alittle.......

we did get a good thunderstorm about a month ago though.... best for years.....

Yeah I reckon, spent that night trying to stop the house from flooding. the old man copped a bolt up the leg from a lightning strike hitting the water we were bucketing out .... ahh the memories

Edited by Ol_Mate
you want rain, have a look at port headland. you can see the bloody cyclone.

http://mirror.bom.gov.au/products/IDR162.loop.shtml

That's f**kin nuts

did you see it during larry last year....

in fact monica was worse a far as rain went. it pissed down for nearly two months,,,,,,,

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Not sure the US can import anything other than the C34 Stagea's, but if you can and you need to to tow, DO NOT under any circumstances get an M35 Stagea. If it is just as a family car and your country/state allows it, absolutely and definitely get an M35 (3.5L if possible as it is effectively a 350Z) over a C34.
    • Punch your VIN (nm35-xxxxxx) into Amayama.com You can see everything there quite easily.
    • Thanks for that, I'll check it all out. I can always do the brakes last anyway if its a problem.  The 16's are super cool, if they do fit I'll cruise around with them for a bit.  
    • Well, that's kinda the point. The calipers might interfere with the inside of the barrels 16" rims are only about 14" inside the barrels, which is ~350mm, and 334mm rotors only leave about 8mm outboard for the caliper before you get to 350, And.... that;s not gunna be enough. If the rims have a larger ID than that, you might sneak it in. I'd be putting a measuring stick inside the wheel and eyeballing the extra required for the caliper outboard of the rotor before committing to bolting it all on.
    • OK, so again it has been a bit of a break but it was around researching what had been done since I didn't have access to Neil's records and not everything is obvious without pulling stuff apart. Happily the guy who assembled the engine had kept reasonable records, so we now know the final spec is: Bottom end: Standard block and crank Ross 86.5mm forgies, 9:1 compression Spool forged rods Standard main bolts Oil pump Spool billet gears in standard housing Aeroflow extended and baffled sump Head Freshly rebuilt standard head with new 80lb valve springs Mild porting/port match Head oil feed restrictor VCT disabled Tighe 805C reground cams (255 duration, 8.93 lift)  Adjustable cam gears on inlet/exhaust Standard head bolts, gasket not confirmed but assumed MLS External 555cc Nismo injectors Z32 AFM Bosch 023 Intank fuel pump Garret 2871 (factory housings and manifold) Hypertune FFP plenum with standard throttle   Time to book in a trip to Unigroup
×
×
  • Create New...