Jump to content
SAU Community

Recommended Posts

Hey guys

just wondering from a few of you with a bit of experience with drag racing in skylines, what would 50rwkw be worth in an r32 gtst??

I had a r32 a few yrs back which made 125rwkw (i dont care how low you think this figure is) and ran a 14.1 with a slightly slipping clutch.

Ive just had my car tuned and was told it made approx 175rwkw on the same dyno. Now the dyno is known to read up to in one case 40rwkw low, so i cant trust reading other ppls power figures to time run. With a decent run and the fact i have a very good clutch now rather than when i had a stocko on the original car what time do you think it would run realistically?

Thanks for your help.....Brett

Link to comment
https://www.sau.com.au/forums/topic/160577-whats-50rwkw-worth-down-the-strip/
Share on other sites

to get a 14.1 with 125 kw is pretty impressive, maybe too empressive. did you get it dyno'd at the same place? i have 169 rwkw and with street tyres i have a 13.7 and i have been told that is good. 14.1 is a good time for a skyline, so with the right driving you probably get low 13's

I think one of the guys in a R32 GTST(RB25turbo) with around 180-190rwkw did a 13.6 pass.

well there is only one way to find out go down to the strip and see what it can do,

you can never trust dyno figures its a tool for tuning :(

You need to mention trap speeds. ET varys on power deliver and traction.

For example, I ran 13.3 with 215rwkw. Sounds about normal depending on what type of car and weight. But I did it at 114mph. So initially you could think that that was about right maybe a bit slow. Then when you mention the MPH you can see that there is power there but it hasn't been used efficiently.

to add further i ran a 13.4 with a trap speed of 103.5mph, the 10mph difference but only 0.1 sec slower. his car is more powerful showing greater speed but mine was a tidier run, more effective use of power. could be slipping clutch, wheel spin, poor launch, slow gear change, missed gear, bad tune.

Chris Davey: Is that 215rwkw in a Corona or R32 R33 GTS?..

Bretto:

When you do your run as Nismo_God has said; 60ft, Trap Speed & ET are all important factors to consider when judging your power.

have fun! >_<

thanks for the reply's ppl.

firstly yes it was at the same shop.

gt shortie i agree, thats why i asked, not sure if i wanna run it for fear of breaking something :ermm:

it was just under 100mph, but it was yrs ago, but i remember that. like i said the dyno is known for reading very low power figures. thats why im not worried about the 125rwkw (on that note, he had a stock standard r32 gtst on the dyno and it made 80rwkw, that should give u an idea of how low the dyno reads). after reading the rb25 turbo upgrade post on here and seeing some power figures some ppl are making with dyno graphs it makes me laugh.

Edited by bretto
  • 2 weeks later...

I can't see you breaking much with 175rwkw. Take it down and let us know how you go.

To add to the thread. How much difference do people think 50rwkw will make at higher power levels?

GTShortie I think got a 12.7 or 12.6 last sunday and I got a 12.4. I think he has about 50rwkw less than me but probably a lighter car. Mine is 1580 with me and a full tank.

The lower the initial power (ie 125rwkw) the more difference the extra 50rwkw will make.

ie; The improvement in time from 125-175rwkw (maybe 0.5-0.7sec) than you will if you go from say 700-750kw (maybe 0.1 or 0.2sec).

  • 2 weeks later...
  • 1 month later...

As someone mentioned you cant say 50rwkw equals x amount of tenths of the time as it depends on the initial power the 50rwkw was added to.

A 50kw increase on a 500kw car is a power gain of 10%. Whereas in your case the 50kw going from 125 to 175kw is a 40% power gain.

And you cant compare to other peoples results as you mention the dyno you went on is a little out of whack.

Which leaves only one way to find out.....

burnsie - as was stated the mph will be a true indication to power - your 13.9 was a very clean run, everything worked well.

my car just with the cat back did a 14.5 @ 95 with a 1.9 so around the 140-150rwkw

Chris - that 114mph is good for mid to high 12's!!!

  • 1 month later...

found this thread and have some more to add...

i ran a 13.426 with 1.970 60ft at 103.5mph with 169rwkw

now i rana 13.081 with 1.911 60 at 104.25 with say around 206(boost was higher then previously dyno'd)

so with an extra 35-40kw i made up 0.35 of a second....and not even 1 mph faster....

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The car/ECU will have all the sensor that it needs and expect to have. I think i do not have to explain to you how the Link is way better specialy if you have swapped engine   I just do not want to deal with any "problems" cuz i have only Nistune which i learned is not that great and in my case cant even deal with that speed problem (Link can) And of course it will be way more easier to tune and diagnose and safe. And for the ECU/speed problem...i dont know.
    • Per Mark Roberts of Sonictune: Mark Robert Author At this time, no. No ETA either 2016-17 models. You will be able to purchase and install a 2018.5+ TCU though   TCU purchasing and pricing info! As we near the release of TCU tuning, I am going to answer some questions I get asked often.   What do I need for TCU tuning? At this time, you will need a 2018.5+ TCU to be able to tune. If you have a 2016-to early 2018, you will need to replace your TCU with the newer version. One good way to know if your TCU is good is if you have auto upshift in manual mode in 1st gear around 6500 rpms. If your manual 1st gear goes to 7k rpm and will hit the rev limiter unless you shift, you have the older TCU.   Why do I need to buy another ecu license/phone flash if I already have it on my ECU tune? The TCU is its own computer module. It is completely separate from the ECU. Because of this, you will be required to purchase a TCU license and, if your tuner has it, the phone flash license required to tune it via phone/bluetooth.   Do I need TCU tuning? TCU tuning is NOT required. However, the faster your setup, the more it will assist in track and dragy time consistency.   If I’m ECU tuned by (tuner A) can I get my TCU tuned by (Tuner ? Yes, since it’s a different module and a completely separate flash, you can have two different tuners. However, it is highly recommend that you have both tuned by the same tuner. For me, my TCU tuning will directly complement my ECU tuning style and features and running my ECU and another TCU or vice versa MIGHT cause some issues. At this time and for the foreseeable future, I will only be tuning my current ECU tuned customers TCUs.     I have a SYVECS AWD controller. Do I still need it? Yes! The AWD controllers main job is to control your AWD system. However, with TCU tuning, you will no longer need the auto-shift function as that will be done through the TCU. The AWD controller will still be very beneficial for racers looking to maximize traction on the launch.     Shift schedule changes: holding gears longer at lower pedal input as well as max shift rpm changes. Please note, the new ECU race rom coming out will address 90% of the shitty drivability issues these cars have through custom maps from myself and Racebox—as well as others I am sure.   Increase shift speeds: as seen in the videos I’ve been posting, the TCU shifts much faster once tuned.   Increased shift pressures: as also seen in the videos, much firmer full throttle shifts.      
    • Per Mark Roberts of Sonictune:     Mark Robert Author At this time, no. No ETA either 2016-17 models. You will be able to purchase and install a 2018.5+ TCU though   TCU purchasing and pricing info! As we near the release of TCU tuning, I am going to answer some questions I get asked often.   What do I need for TCU tuning? At this time, you will need a 2018.5+ TCU to be able to tune. If you have a 2016-to early 2018, you will need to replace your TCU with the newer version. One good way to know if your TCU is good is if you have auto upshift in manual mode in 1st gear around 6500 rpms. If your manual 1st gear goes to 7k rpm and will hit the rev limiter unless you shift, you have the older TCU.   Why do I need to buy another ecu license/phone flash if I already have it on my ECU tune? The TCU is its own computer module. It is completely separate from the ECU. Because of this, you will be required to purchase a TCU license and, if your tuner has it, the phone flash license required to tune it via phone/bluetooth.   Do I need TCU tuning? TCU tuning is NOT required. However, the faster your setup, the more it will assist in track and dragy time consistency.   If I’m ECU tuned by (tuner A) can I get my TCU tuned by (Tuner ? Yes, since it’s a different module and a completely separate flash, you can have two different tuners. However, it is highly recommend that you have both tuned by the same tuner. For me, my TCU tuning will directly complement my ECU tuning style and features and running my ECU and another TCU or vice versa MIGHT cause some issues. At this time and for the foreseeable future, I will only be tuning my current ECU tuned customers TCUs.     I have a SYVECS AWD controller. Do I still need it? Yes! The AWD controllers main job is to control your AWD system. However, with TCU tuning, you will no longer need the auto-shift function as that will be done through the TCU. The AWD controller will still be very beneficial for racers looking to maximize traction on the launch.     Shift schedule changes: holding gears longer at lower pedal input as well as max shift rpm changes. Please note, the new ECU race rom coming out will address 90% of the shitty drivability issues these cars have through custom maps from myself and Racebox—as well as others I am sure.   Increase shift speeds: as seen in the videos I’ve been posting, the TCU shifts much faster once tuned.   Increased shift pressures: as also seen in the videos, much firmer full throttle shifts.      
    • The fancy pants red shock tower brace is finally incoming from MX5 Mania, getting it shipped from 'Merica has been a long and problematic process, and GWR, the 'Merican supplier will not ship directly to consumers outside of the US, Mania basically had to order a heap of them, the colour choice was silver, or red, and we all know anything red adds 5 killerwasps of dynotorques..... Whilst it does fit over a 2.5, and I've seen a few photos and videos of it being installed and fitting, google also says it might get real close to the FAB9 intake front runner, people in the US says it does fit with the FAB9 intake, except for one person who said it slightly touched.......so there is that.....LOL..... As it seems that I am the first in AU to have this combination of parts there's no local knowledge about fitment, so I'm just a willing guinea pig in this endeavour, I'll cross my fingers and toes and hope for the best In other news, I ordered stuff from China  on the same day I ordered the 23° silicone bend from Victoria, the stuff from China arrived a day ago, the 23° silicone bend is still travelling around Australia thanks to Australia Post, and "may" be here next week
    • Very good news...I contacted Racebox about it last night. My car is a 2016 so remains to be seen if it is compatible, requires a TCU swap, or is impossible.
×
×
  • Create New...