Jump to content
SAU Community

Recommended Posts

  • Replies 765
  • Created
  • Last Reply

Top Posters In This Topic

Quick update Trent

Got sent a map from one of the guys on the SOC forum and tried it last night and the car ran perfectly. Came to the car this morning and running rough as hell again, with a definate smell of petrol until the engine died. Reconnected the stock ecu and ran fine. Drove the car 25 miles to work no problem. At work reconnected the emu and now the car won't even start. Is this starting to indicate a potential problem with the emu hardware? Harness should be OK, as it is a genuine Greddy N4 harness. Totally lost what to do next other than chuck the lot in the bloody bin and give up! :O

I've come across one annoying problem with the emanage, while stuffing around with the laptop when connected to the emanage with the car running somehow the map becomes corrupted and car runs megga rich on idle and can't rev past about 2 grand. However the problem is easily fixed, start a new map and then copy all the infomation across to the new map and car runs fine again....wierd.... its done this to me twice now.

Anyone know what a safe rev limit is on RB25 I want to push it up just a bit to say 7200, 6800 doesn't seem enough.

Edited by SevenAngryPenguins

I've had that happen too, but not since the latest software upgrade. When it's happened I've looked at the datalog and the emu has stopped outputting an afm signal. Start a new map and it's all fine again.

The hydraulic lifters on mine started complaining at 7500 so I wouldn't go above 7200. Personally, I left it at 7000 as I really don't need any more revs. Especially with a 3.7:1 ratio diff :O

I've had that happen too, but not since the latest software upgrade. When it's happened I've looked at the datalog and the emu has stopped outputting an afm signal. Start a new map and it's all fine again.

Yeah there was an old glitch in the software that did that on occasion but the new updates have cleared that up.

Quick update Trent

Got sent a map from one of the guys on the SOC forum and tried it last night and the car ran perfectly. Came to the car this morning and running rough as hell again, with a definate smell of petrol until the engine died. Reconnected the stock ecu and ran fine. Drove the car 25 miles to work no problem. At work reconnected the emu and now the car won't even start. Is this starting to indicate a potential problem with the emu hardware? Harness should be OK, as it is a genuine Greddy N4 harness. Totally lost what to do next other than chuck the lot in the bloody bin and give up! :O

is the temp reading accurate i the EMU datalog? if not you need to swap jumpers. D board does not have the inbuilt temp vs inj adapter built in.

Yeah there was an old glitch in the software that did that on occasion but the new updates have cleared that up.

which software update is that? I'm running 2.16 downloaded from mohdparts.com

which software update is that? I'm running 2.16 downloaded from mohdparts.com

yeah, is the emu updated? as i have not had that issue for months now.

um, emu has the 2.16 firmware as well it seemed to of done it when the laptop shut down and had to be restarted, well I think

yeah check it updated, then load say rb20 into your EMU then start a complete new rb25 setup file and load that into the EMU and see if it fixes your issues.

ok will do I'm pretty sure it updated the first time I connected it after the update though. Your boost cut settings worked as well thanks for that, I just had to change one of the settings a bit lower and it was all good. I Think my rubber intake was sucking closed as well, I reinforced it after the boost cut settings didn't work at first.

Edited by SevenAngryPenguins

Hi guys.... I plugged in and turned on my EMU yesterday. So many questions....

Firstly, I have a D board, is this a major issue???? Trent, if it is, can we do a deal re your spare E board?

Secondly, when I had it on the dyno (I got some free time from a place I used to work at), I couldnt make any changes stick.... I.e. whenever I changed the airflow adjustment map, the stock ECU brings the values back to lambda.... How do i get rid of this, as in turn on closed loop?

I'll think of some more no doubt

Hi guys.... I plugged in and turned on my EMU yesterday. So many questions....

Firstly, I have a D board, is this a major issue???? Trent, if it is, can we do a deal re your spare E board?

Secondly, when I had it on the dyno (I got some free time from a place I used to work at), I couldnt make any changes stick.... I.e. whenever I changed the airflow adjustment map, the stock ECU brings the values back to lambda.... How do i get rid of this, as in turn on closed loop?

I'll think of some more no doubt

if you want to tune in closed loop areas disconect the o2 sensor. Also dont use the airflow adjustment map use the injector map.

happy tuning :thumbsup:

I have a question regarding the airflow adjustment map. I have been tuning the car using the injector map and have got the afr's pretty good but not quite perfect as the afr can change a little bit from within the same rpm tuning square. I think I read in this thread somewhere that you can use the airflow adjustment to fine tune the afr by changing the maps scale for finer adjustment. Is this still possible when my airflow meter is maxed out? I only really want to clean up my high rpm afr's

I have a question regarding the airflow adjustment map. I have been tuning the car using the injector map and have got the afr's pretty good but not quite perfect as the afr can change a little bit from within the same rpm tuning square. I think I read in this thread somewhere that you can use the airflow adjustment to fine tune the afr by changing the maps scale for finer adjustment. Is this still possible when my airflow meter is maxed out? I only really want to clean up my high rpm afr's

use injector map 2 and set your scale from where you want to clean up, for example you have a weird spot at 6250 you camn actually run the map scale from 6000 to 7000 (6000-6500 etc) and have the scale real specific around your problem (see attached pic)

you can do the same with timing. All secondary maps work on top of map 1 so any adjustments on map2 will be added to map1 ; so if you have plus 15% fuel in map1 at 6250 and 5% at 6250 in map2 you will have a total of 20% extra fuel at 6250.

hope it helps

post-34927-1212502312_thumb.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • Seat of the pants assessment of the new intake: The car is way less "doughy" when hitting the loud pedal, especially off idle when stopped or in traffic, I did use a cheapo lazer thermal thingo to measure the temp around where the pod filter got its air, it was between 55 - 60°C, in saying this the car was shut off and not moving, so the OEM intake pipe was not supplying any fresh air to where the pod was when the car was at least moving A weird bonus was induction noise on the throttle in the cabin increased a bit,  I was worried that I was actually going to lose some of that induction noise I love so much, outside though, when I got the daughter to do a WOT drive by pass for me, the induction noise has increased alot when on the throttle, not quite ITB doort, but well up there I'm extremely happy with the results and have been exploring the country roads in the region  As for house mods: 1.New front fence is up and is awesome, it really upgraded how the joint looks from the street, and the added security is nice 2. Electricians have replace some interior lights, and with more lighting in the garage, a few new motion detecting lights out the front above the garage, front room, and at the front door, which I have already found heaps helpful coming and going, also now has fancy pants CCTV all round the house The only hold point for power though is the solar and batteries due to supply issues, although this will happen over the next few weeks 3. I have done a heap of landscaping out the front and I'm almost ready to do a new small retaining wall with some nice blocks to replace the brick and cemented in rocks around the raised garden beds cemented in river stone "was the fashion at the time" the house was built. I currently have a pallet of retaining wall blocks and 2 bulka bags of 20mm blue metal to replace the wood chip that is in the raised garden beds around the house 4. I now have 3 big raised garden beds for out the back to grow some vegetables, about 70cm high, 200cm long and 100cm wide 5. My 2 compost bins are already pretty full with brown, green and kitchen waste from the landscaping I'vedone so far, but they will probably take a few months to break down, so anything else that gets chopped, trimmed, and kitchen waste will just start filling the base of the raised garden beds to about 30cm before I start throwing 40cm of good compost, and stuff, for the vegetables to grow in, I'll need a few ton of compost and soil, but the local supplier can sent me bulka bags of the stuff Basically the logs, wood chips and a few strategically placed rocks for drainage, will give the beds some good organic materials down low to break down over time, and they will hold moisture during the warmer months to save the water in my big arse water tank if we don't get alot of rain So, all in all, the car and house mods are going well, and I'm really enjoying being retired, I sleep in too 0700 and slowly plod around inside until I feel like actually doing anything, and only work in the yard for as long as want, which has actually been alot over the last few weeks,  although when you look at it, it seems that not a huge amount of work has been done,  until I look at the before I started the work pics Happy days and good times indeed 
    • hahaha yeah. Plan is to get side skirts and probably just rear pods. But going to do them one-by-one. I've got a set that I really like from RHDJapen, but that one isn't shipped to AU. So need to find someone who can get it for me
    • Here's an idea, answer the questions I asked you as they are trying to work out WHY the LSD will be binding up in a straight line.
    • You haven't driven many modern cars then have you? Most of them have sfa steering feel with their stupid electric bullshit steering systems.
×
×
  • Create New...