Jump to content
SAU Community

32 Gtr Standard Bov's, Rear Seat,33 Clear Indicators Rb26 Tming Belt Cover. Gtr Or Gtst Boot Lid


Recommended Posts

Hi Guys

After some help sourcing a couple of parts,

Ineterior mats

RB 26 Timing belt cover, not clear

33 GTST side clear indicators

32 RB26 Rear seats

32 RB26 standard BOV's

32 GTR/GTST boot optional with GTR wing

32 GTR strut bars front and back, good condition or near new

I am based in Brisbane but can travel up and down the coast, have contacts in other states to pick up or organise post.

Best to e-mail [email protected] or text/ call 0408188777

Thankyou for any assitance that you may give.

I don' have the gtr bov itself, but I have the 2 pipes on both sides that you mount the gtr bovs to. would that help you?

Then you could just source the bovs themselves (when people sell the bovs, they normally don't come with the stock piping.

we can help with a gtst bootlid

Hi, thanks for the reply. I think the transport cost of such a big item will blow out the cost. Thanks anyway

I don' have the gtr bov itself, but I have the 2 pipes on both sides that you mount the gtr bovs to. would that help you?

Then you could just source the bovs themselves (when people sell the bovs, they normally don't come with the stock piping.

Good point , I was hoping to get it all in one. If I cant get the pipes included I will yell out. Thanks for your reply

i got a timing cover sprayed blue mate, if you want it i will do it for $70 delivered to you! let me knwo via pm with your details etc.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The final part arrived today to un-clampify and simplify the intake Who would have though a 1/2" hose stainless bulkhead fitting designed for below waterline bilge pumps would be what I needed Test fit on a 3" offcut I had laying around to see if it would work, and it worked a treat All going well the intake will be on its "final version" tomorrow 
    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
×
×
  • Create New...