Jump to content
SAU Community

Recommended Posts

ok so im new to this forum but im in need of some help from you guys who know your stuff. so i whent and bought a turbosmart bost controller just a t-peice one and fitted it all up tried to set the boost and it wont conrol boost under 0.7 bar thats as far bak as the adjuster winds atm i was jus tlooking to run the 0.5 bar it had been running till i could get it tuned it has and apexi safc not the best but beter than nuthing i guess now my problem is that now when it hits 4000rpm approximatly it starts missing like its going into RnR does this sound right i tried to lean the fuel out a bit with the computer im not to sure if it helped or not and i dnt want ot lean it out to much and course damage so. im positive ive got it set up right from the instructions i got with it says to have the controller flow arrow going towards the actuator is this right? any one who could give me some helpful imformation would be great thanx

oh and if this helps the cars mods are fmic,3'' dump and 3.5''cat back, apexi safc

Link to comment
https://www.sau.com.au/forums/topic/163738-boost-control-issues-help/
Share on other sites

yeh hopfully im going to see a tuner tomorrow as i live in gladstone qld we only have like 1 tuner in town but i guess its beter than none. im just hopin gits not the coil packs earthing out cos they expensive i dnt think it will be because it was fine running 05-06 bar with tahndard boost solinoid i think its just getting into rich and retarded so hopfully the safc can tune that out it ws in the car when i got it one day ill get around to getting a new ecu

ok so ive got it booked in for a tune and i got rid of the misfire it was just going into RnR like i suspected but there is still one weird thing i cant work out when u exelerate hard in 1st the boost goes to wear its set till about 4000rpm then just tails out and drops rapidly is this normal or is sumpthing wrong it dosnt do this in any other gear and still runs fine in 1st just does that so anyone who noes why its happening le tme no plz thanx in advance

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I don't know for sure, but I'd expect them all to be interchangeable given the diff end and hub end don't move/change between any C34 series. Often Nissan will change part numbers and the aftermarket follows those year ranges; but the original part number change doesn't mean other parts won't fit. The change could be a change in material, internal parts or even just supplier. For example, all the RB gearbox to engine bolts are no longer available and there is a new part number instead. The only change is they went from cadmium plated bolts to zinc plated due to the issues manufacturing with Cadmium. They look different but work the same.
    • One year is a bit concerning. Did you try contacting GSP? It says 5 year warranty on the box if I remember correctly. I'm also running their driveshafts on my S2 Stagea.   You could check the part numbers on Amayama for your year. Here's the link for my 1998 which gives the 39100-23U60 part number. Well, that and 39100-23U70. https://www.amayama.com/en/genuine-catalogs/epc/nissan-japan/stagea/wgnc34/6649-rb25det/trans/391 What does it say for yours?
    • I ordered a GSP Front R/H Axle from here - https://justjap.com/products/gsp-premium-front-driveshaft-r-h-nissan-r32-r33-r34-skyline-gtr-stagea-4wd#description It lasted around a year before one of the boots blew out. I'm lowered, but I have GKTech roll center adjusters. One year seems a little premature. I think I'm going to spend the extra money on an OEM cv axle this time. This website - https://tfaspeed.com/collections/nissan-stagea-wgnc34-x-four-parts/products/nissan-stagea-awc34-260rs-rb26-right-front-axle-drive-assembly Makes it sound like the readily available OEM CV axle will only fit 11.1999 Stagea and up (mine is a 2.1997 S1). The JustJap listing didn't mention any years or anything for the GSP axle. Amayama shows '11.1999' and up as well for that part number. As well as 'plastic boot type'. See attached picture. So I guess my question is, does that axle (39100-23U60) really only fit S2 Stagea? It's the front driver side. If it does, I'd love to buy that instead of rolling the dice on another GSP. I've found that OEM one cheaper here: https://www.partsfornissans.com/oem-parts/nismo-jdm-r32-r33-r34-skyline-gtr-r32-gts4-right-front-axle-3910023u60 and here https://www.nissanparts.cc/oem-parts/nismo-shaft-ft-drive-3910023u60 Just a little confused because the JapSpeed listing for the GSP front driver axle doesn't mention any specific years or anything and it fit my S1 Stagea fine. So will 39100-23U60 fit my S1 Stagea even though technically it says '11.1999' and up? What would have changed? Thanks.  
    • Thanks for the info. The only "Issue" I've had with the shifter is I always found the throw between 4th and 6th gear too close. I'm always worried to shift into 4th accidently and sending my motor to the moon. Adam LZ recently came out with a video and stated Serialnine revised their shifters to correct this and will change all the revised parts for 150$. Strangely enough, I contacted Serialnine right after and they denied it and said it's bullshit. I found that strange as he's a distributer. I'll keep this forum post updated on that saga.
    • Yep that is correct. It allows you to adjust the short throw range from what I can tell
×
×
  • Create New...