Jump to content
SAU Community

Recommended Posts

  • Replies 43
  • Created
  • Last Reply

Top Posters In This Topic

might be worth checking the injector if in doubt switch it with another cylinder. Comp test it and see what happens!

yeah im hoping it might be injector or injector solders or something

but gotta drive it home! cant leave it in the work car park over night!

but of a thud thud clank coming from under the car but thinking its the exhaust hitting stuff because its running so rough

Link to comment
https://www.sau.com.au/forums/topic/164278-ohh-nooooo/#findComment-3045332
Share on other sites

hey ed sorry for the simple q, but what are the signs that the engine has dropped a cylinder? would it be similar to an engine missing?

oh yeah.. got the coilpacks tues and went back to the old plugs and worked a charm, fixed my missfire.

Link to comment
https://www.sau.com.au/forums/topic/164278-ohh-nooooo/#findComment-3045354
Share on other sites

It does sound like shes dropped a cylinder, The only thing you can do is comp test it and go from there really. Its not like an injector to just give way like that but it can happen.

If you have changed the plugs and switched coils etc its not lookin good. If you need help sourcing another engine or getting it fixed let me know. Got enough RB20 crap laying around to get it running again!

Link to comment
https://www.sau.com.au/forums/topic/164278-ohh-nooooo/#findComment-3045364
Share on other sites

i did the injector wiring myself so ill give it a wiggle and see if it comes back to life, but im pretty sure i have dropped a cyl....

ill buy a comp tester from supercheap tonight and bring it back to work to test it...

reckon its safe to drive home through the cross city tunnel or will i just do more damage?

desperate for any help anyone can give!

Link to comment
https://www.sau.com.au/forums/topic/164278-ohh-nooooo/#findComment-3045369
Share on other sites

wet and dry? dont i get some guage thing that i screw into the sparky hole and see what psi its got?

its just a 5min drive so hopefully she gets there!

i guess if it was something bottom end like bearings or what not i would dropped more cyls?

i know alot about cars but nothing about engine blow ups! never experienced one before

Link to comment
https://www.sau.com.au/forums/topic/164278-ohh-nooooo/#findComment-3045402
Share on other sites

compression test it first.

stick a rag on the end of a screw driver and put it inside the spark plug hole, if it comes out clean then you're safe. if its got oil in it its time for a rebuild.

or just check the spark plug for oily shit all over it.

Link to comment
https://www.sau.com.au/forums/topic/164278-ohh-nooooo/#findComment-3045413
Share on other sites

ok guys

bought a tester tonight, tested cyls 1 and 5 (problem cyl is 5) did a dry test i think its called and both read 150psi! thats a good thing isnt it! i still need to do a wet test...

checked spark yes, sparkies ok

im 65% leaning towards one of the injectors playing up, OR one of the injector resistors having a melt down seeing as it happened so fast...

the car is at work at the moment, can leave it there most of the weekend, so ill order the $25 resistors and go in with a multi meter and do the wet test...

phew glad she can hold some pressure!

Link to comment
https://www.sau.com.au/forums/topic/164278-ohh-nooooo/#findComment-3046121
Share on other sites

I know someone not too far from you who can check your engine well and truly. All your cylinders will have the same comp readings, guaranteed...

...but the insides might look a bit mangled. His name starts with an 'H' and rhymes with 'vermin' :pwned:

Seriously though, hopefully it all turns out ok mate.

Link to comment
https://www.sau.com.au/forums/topic/164278-ohh-nooooo/#findComment-3046155
Share on other sites

I know someone not too far from you who can check your engine well and truly. All your cylinders will have the same comp readings, guaranteed...

...but the insides might look a bit mangled. His name starts with an 'H' and rhymes with 'vermin' :pwned:

Seriously though, hopefully it all turns out ok mate.

how long have you been drinking for hahahahahaahahhah i totally didnt get that!!!

wont have much time to do the car tomorrow so saturday it is, just ordered new resistors so ive got a backup!

damn cars!

Link to comment
https://www.sau.com.au/forums/topic/164278-ohh-nooooo/#findComment-3046160
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • If as it's stalling, the fuel pressure rises, it's saying there's less vacuum in the intake manifold. This is pretty typical of an engine that is slowing down.   While typically is agree it sounds fuel related, it really sounds fuel/air mixture related. Since the whole system has been refurbished, including injectors, pump, etc, it's likely we've altered how well the system is delivering fuel. If someone before you has messed with the IACV because it needed fiddling with as the fuel system was dieing out, we need to readjust it back. Getting things back to factory spec everywhere, is what's going to help the entire system. So if it idles at 400rpm with no IACV, that needs raising. Getting factory air flow back to normal will help us get everything back in spec, and likely help chase down any other issues. Back on IACV, if the base idle (no IACV plugged in) is too far out, it's a lot harder for the ECU to control idle. The IACV duty cycle causes non linear variations in reality. When I've tuned the idle valves in the past, you need to keep it in a relatively narrow window on aftermarket ecus to stop them doing wild dances. It also means if your base idle is too low, the valve needs to open too much, and then the smallest % change ends up being a huge variation.
    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
×
×
  • Create New...