Jump to content
SAU Community

Recommended Posts

hey guys

selling these:

BODY:

r32 door mirror's-

r32 2dr drivers door-

r32 2dr passenger door-

r32 REAR reo bar -$130

r32 type-m rear bar -$100

r32 type-m passenger side skirt-$75

r32 shell- 1k

ads23213.jpgbar.jpgreo.jpgside.jpg

DRIVELINE:

r32 gtr/gts4 driveshaft -$150

r32 gtr/gts4 tailshaft - SOLD

A pair of R32 GTR/GTS4 6 bolter rear 31spline 6bolt Axle's - $150

adadadsa2.jpgas33.jpg

SUSPENSION & BRAKES:

R32 GTR front caliper's- offers

r32 type-m rear calipers-offers

full set of r32 GTST M-spec rotors- offers

r32 rear 5 stud hubs with LCA-offers

r32 tein fronts gts4/gtr -

r32 koni rear 2 point height adjustible shocks gts4/gtr-

rear r32 2dr handbrake lines-

wae24ed3.jpgsus.jpgp10retret.jpg sad321.jpg

LIGHTS

r32 type-m fog lights (pair)-

passenger side headlight-$70 ( comes with most of the wiring)

wqe213ads2213.jpgwqewq.jpg

WHEELS

16" 5 stud dishies 8" wide-offers

OTHER

r32 gts4/gtr/gts/gtst ABS unit -offers

interior parts:

r32 2dr rear trim under 1/4 window -$150 both for lhs+rhs

RHS r32 2dr 1/4 window surround- $50 SOLD

rear view mirror-

r32 1993 spec rear seats-$200

r32 gtst steering wheel- ok conditon $100

r32 interior goodies- mostly perfect condition ~take wat u need~ - make an offer

p1010048.jpgp1010045.jpg rearseats2.jpg

let me no

in melb

i might hav sum more so let me no wat u need

Edited by Dan_J
Link to comment
https://www.sau.com.au/forums/topic/164334-delete/
Share on other sites

blinko : think i got it, you mean da left kick panel on da drivers side?

wannabeslida : yea i'll pm da price and price for postage soon

LoNg_ShaNks: no aircon vents only heater vents

ducki: sorri no rad

Edited by Dan_J
Link to comment
https://www.sau.com.au/forums/topic/164334-delete/#findComment-3047497
Share on other sites

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Need to see other side of PCB in that area...ie; I don't see any thru-hole mounting, just soldered vias (smd zeners in SOT23 have 3 legs but only 2 are used, as reflected by PCB tracks)
    • 4 to 5 is fine. It will be slow, but that's better than blowing turbos. I don't have a PS pump idle up solenoid on my car, because... I think when we put the Neo in we retained my R32 lines. But.... From inspecton of the R34 vacuum hose diagram, you can see that the solenoid needs to be connected to the turbo inlet as source of clean air) and the plenum (as source of vacuum - which is the place for the air to flow to to cause the idle to increase). So 3 to 1 is VERY WRONG. 3 should go to either the turbo inlet, or the plenum. Follow the other hose from the PS solenoid and if it goes to the plenum, then your 3 goes to 2 2 would also serve as a bleed port for a boost solenoid.
    • Pull them out and pull more apart. You can't do shit with them still bolted to the floor of the car.
    • Yes it is. ZD1 is on the other side of the board. Where ZD1 is marked is clearly opposite a 2 pin device. Our 3 pin device here is not a ZD.
    • Alright, a little update on this... I called Fulcrum, who used to be the distributor in Australia. No Bueno, they don't service them anymore.  Called shock works, who don't service them but offered to dyno the shocks for performance, and suggested DNA in Sydney might service them.  Called DNA, who also do not service them and basically said they try to steer customers away from tein for this exact reason these days- there is just no support for them anymore apparently.  Both SW and DNA said they are a not necessarily a bad product, but they just don't service the brand or know anyone who does service the brand anymore.  So... I could keep calling around but at this point I think I'll probably just spring for the shockworks product, unless anyone here knows anything.  Cheers 🍻 
×
×
  • Create New...