Jump to content
SAU Community

Recommended Posts

hey guys

so i heard my friend from nissan silvia saying that they used to go on ghost runs. apparently they go to all the "haunted" places around the brisbane region.

has anyone been on one? or would anyone be interested in going on one on the 21st (next saturday)

Edited by R33_Rob
Link to comment
https://www.sau.com.au/forums/topic/164567-ghost-run-anyone/
Share on other sites

lol

ive been on holidays for a week. i meant the 21st of april, my bad sorry guys hehehe

so does anyone know where to get. i have heard of a few things. if someone knows a fair bit about this sort of thing maybe they should lead the cruise.

i was thinking we should meet somewhere like milton maccas (only because i know where that is). when i get back from uni ill try to find this "haunted" jail somewhere.

Yes somewhere at the toowong cemetary if you put your car in neutral and take the handbrake off then you will roll up the hill. Im assuming this is due to iron deposits closeby. can anyone else verify this

I heard at the toowong cemetery or somewhere near there there is a phenomenon where when you park your car on a slope and leave the handbrakes off, instead of sliding downhill, your car will slide up.

That is Lutwyche cemetery and it doesnt work. I have tried it. There are a few haunted sites around brisbane. I have done the boggo rd jail ghost tour.

http://www.ghost-tours.com.au/Pages/tour_b...ail_details.htm

It is quite interesting and good for a laugh. Could be worth getting a few people together for this perhaps.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • There are several aftermarket options available, from not-too-painful moneyhttps://justjap.com/collections/driveshafts-bearings/products/d-max-reinforced-replacement-rear-driveshaft-set-fits-nissan-s13-s14-s15-r32-r33-r34-c35 and  https://justjap.com/products/crank-motorsport-billet-rear-axles-fits-nissan-skyline-r33-gts-t-r34-gt-t?srsltid=AfmBOorQk4xkGUa98kO7v2ePLUiNt-HRrM2AwWNw9mbSIVE1ujBVwY__, all the way up to The Driveshaft Shop https://driveshaftshop.com/skyline-cv-axles/
    • Yeah based on old XRC5964S specs, it looks to be roughly GTX3576R sized? But this 5964S compressor will flow 90lb airflow somewhat similar to the compressors in both the GTX3584RS or G35-1050.. I fully expected the 0.64 rear A/R to choke up top - seems way too small from typical convention - but these are seemingly beneficial over the prior 0.82 results.. Be interesting to see if he comments on the EFR question in that thread - he mentioned in a prior video that BW EFR's were the "cats pajamas 10 years ago", but by the sounds of things all his kits have been using Xona for quite a while now.
    • Yeah it’s still got the oem manual gearbox and clutch, only kinda mods are a blow off valve, coil overs, and a aftermarket intercooler. Also had it for about 2 months now with a lovely midnight purple paint on it.
    • Yeeeppp, been following a lot of the testing on the latest Xona stuff and there are some mental results.  He also went over 1000hp @ 4 hubs on his Mainline with a XRE6364S (63mm) which was also well into the 20psi range before 4000rpm on a 2.5. Crazy stuff. Fwiw the XRE5964S is basically the modern equivalent of their old HTA3582 - would drive nicely enough on an RB25 or 26, but proven capable of a huge amount of power if you want to spicy with rpm tho even at sane boost levels will make stout numbers 
    • The axels in my R33 seem tired, and have a bit of play in them. I cannot find any new of course, not interested in buying used, but I am looking to see if anyone can identify some cross compatible axles. In the states I have seen suggested for S chassis the J30 axles, however for the skyline (as best I can tell) the lengths are about an inch off (2.5cm) on both sides. R33 my measure L 22" R 24.5" GPT L 22.5" 24.25" J30 L 23.5" 25.5"  so shaft length is probably an inch wider. Not sure if someone has another still remanufactured option besides the J30. I figured worst case I can buy a pair tear them down and swap the center shaft. My other option was reaching out to GSP to see if they cannot piece together a set, since the axle stubs are still manufactured, I wouldn't think it be that hard to find a shaft or make a shaft work. 
×
×
  • Create New...