Jump to content
SAU Community

Recommended Posts

Ok, i figured other forums i frequent have them as well

please post as many specs of your wheels as possible

width and offsets being the MOST important

Picture from the side straight on, and one from the front straight on (to see if they stick out, or sink in for fitment wise)

ill start

Stock M35 wheels.

15mm spacers front and rear to clear GTR brakes

225/50/17 tires

17x7 id imagine is waht it looks like

383528502_13d43d07ff.jpg

383528569_5856cb5a76.jpg

Work euroline

18x9 -5

18x0 +20

235/40/18

400501903_42836c68bd.jpg

400501941_265dd452bc.jpg

400501811_a1f0a65d3f.jpg

above is with stock fenders

below is with midified fenders

406702878_99e1df16bd.jpg

406702791_5d46ba756f.jpg

Work Emotion XD9

18x9 +20 all around +20mm spacer on the front

225/40/18

453749229_cabaf516a7.jpg

453749179_9735cbd03b.jpg

please contribute

Link to comment
https://www.sau.com.au/forums/topic/164936-post-your-wheelstire-size-and-specs/
Share on other sites

  • Replies 67
  • Created
  • Last Reply

Top Posters In This Topic

17 x 9 - Standard R33GTR wheels with 245/40/17's

Pictures are at 340 mm front and 330 mm rear, which was too low. It's now at 355 mm front and 350 mm rear, much better ride and handling.

R33GTR_Wheels_340mm_Side.jpg

R33GTR_Wheels_340mm_along.jpg

:D cheers :(

  • 4 weeks later...

18x10 +20

dont get a 10 in the rear unless you get at LEAST a +10

but hten you will haev to do an agressive roll and pull in the rear.

anything less will hit your coilover.

18x10 +20

dont get a 10 in the rear unless you get at LEAST a +10

but hten you will haev to do an agressive roll and pull in the rear.

anything less will hit your coilover.

Your using 235's on 10 inch rims as per per your first post?

They would look mega stretched?

A "normal" person would use a smaller width rim and run the correct width tyre for comfort, looks, handling and safety

am i normal?

I use a 225/40 on a 9 inch wide and a 235/40 on a 10 inch wide

its about clearance, the stretch in the sidewall allows you to run a wider/lower offset without fear of rubbing so when the camber changes in a turn, it acts like a circle and not a square like a normal tire

am i normal?

NO :thumbsup:

That's why you should explain or clairfy when posting esp when people are asking a question about a topic they do not know anything about. Otherwise someone is going go and buy a set of wheels too wide or the wrong offset and have to beat the shit out of the rear guards and run a way too narrow a tyre for the rim size.

18x10 +20

dont get a 10 in the rear unless you get at LEAST a +10

but hten you will haev to do an agressive roll and pull in the rear.

anything less will hit your coilover.

cool...thanks grant.

mate has a set of eurolines ..18*9 and 18*10 ..both with +35 offset...i'll try them for fit this weekend....oh and tyres are 235 at the rear too...really stretchhhhhed

Running Advanti Racing 'Karla" wheels:

Wheels: 19x8 +35

Tyres: 245/35 R19 Hankook K104

They are being replaced (due to a fault) with Enkei RP03 model which should fill the guards a little more, I think.

post-17581-1179964171_thumb.jpg

post-17581-1179964287_thumb.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Depending on how long the car sat it is very possible for injectors to be stuck open or closed, I'd get them cleaned and flow tested. Other than that, obviously when the loom changes and the car doesn't start any more....the loom is suspect so some tracing / comparing may be required
    • Harness is for a s1 Rb25det, and it is engine and lower harness.  the old harness had broken off plugs and was in very rough condition/exposed wires and splices etc. it is not able to be put back on the car, I could visually inspect to see if they had rewired any pins on the ecu plug. The fuel pump definitly isn’t turning off it’s an external pump and very loud you can hear it. Will look at the other harness tonight, am also going to pull the fuel rail and watch the injectors spray, will update here with what I find. Pretty sure at this point it has to be something to do with injectors because car will fire up on starting fluid and cas is clicking the Injectors. Fuel pressure is steady 43psi 
    • Check the injectors flow evenly, and are actually flowing what you and the ECU think they should be flowing. If it's starting up on starter fluid, you have a fuel issue. Is it possible under cranking your fuel pump is turning off?   The harness you replaced, is that the whole engine harness? Do yourself a test, and drop the old harness on and plug it into the Z32 ECU. It's possible they've wired things different. From memory S1 to S2 is different in RB25 and you may have a wrong loom
    • I haven’t pulled the injectors to watch them spray yet but they are clicking from the cas and all of the spark plugs are wet with fuel. I’ve thought the cylinders were being flooded from the beginning and was hoping fuel pressure would fix it. Tonight I am going to pull the rail and watch the injectors spray. Don’t know how to test/diagnose if the plugs are firing in correct sequence but that should be a timing thing and as far as timing goes my car still has the half moon for the cas can only install it 1 way. And my mechanical timing is 100% correct I posted photos above. Confirmed with the balancer on and off. 
×
×
  • Create New...