Jump to content
SAU Community

Recommended Posts

how odd..

So, just to get this right, the waste gate is wired so the flapper is in the open postition..

Then there should be no way that thing should be climbing in boost pressure reguardless of where u get the signal from.

arrghh.. question,

can the wastegate actually 'open' all the way? I mean is it only opening say half way or two thirds?

Are you sure there is nothing in the wastegate dump pipe that is blocking gas flow?

well thats all i got! not much help huh?

Yup I know what your saying, the flapper was definetily wired fully open, infact further than the actuator would normally throw it.

Hmm I had the dump pipe completely out of the car the other day all seemed to be in order, maybe I will need to dig deeper.

I know it sounds impossible, seems impossible to me too :worship:

if the wastegate and actuator are working fine, why not look at other possibilities?

haha i was about to suggest boost controller but u said u dont have one.

i would check vacuum lines and pretty much anything looking for any leaks splits or anything like that.

but hey im no expert.

Cheers lineskee

Na your right, I need to start again at the basics, thanks for your input

Its quite possible the motor is breathing a little better due to the recent inlet mods. That paired with the stock dump that definitely favours turbine flow rather than wastegate flow 'could' tip it over the edge of boost creep.

I'd almost be inclined to again flick that circlip from the wastegate/actuator arm, disconnect it and wire the flap open again.

It just can't/shouldn't over boost with the wastegate wired open.

All bets are still on the stock dump and combination of inlet/breathing mods. :worship:

The problem I have though is a cat back with stock dump/front and fmic is quite a common mod, others don't see boost creep problems, so why do you? :S

Its quite possible the motor is breathing a little better due to the recent inlet mods. That paired with the stock dump that definitely favours turbine flow rather than wastegate flow 'could' tip it over the edge of boost creep.

I'd almost be inclined to again flick that circlip from the wastegate/actuator arm, disconnect it and wire the flap open again.

It just can't/shouldn't over boost with the wastegate wired open.

All bets are still on the stock dump and combination of inlet/breathing mods. :mellow:

The problem I have though is a cat back with stock dump/front and fmic is quite a common mod, others don't see boost creep problems, so why do you? :S

Its cause I'm special :worship:

I'll take it for a longer squirt with the wastegate wired open tomorrow, I agree it should be impossible!

thanks

my old post for your same issue may help, the problem would come and go for me but in the end with the stock 25 in it, it was the intercooler piping causing my issue.

maybe you are special like i was, the previous motor in it was meant to be a 25 until it went bang and when i pulled it down found it had 26 internals with massive cams hence the too munch exhaust flow out of a stock 25 turbo. id be hoping to be special :)

http://www.skylinesaustralia.com/forums/in...=133869&hl=

no dramas mate....

where abouts are you getting the reading for the boost gauge?

is it off the IC piping or the manifold?

was thinking along the lines of what has been said previously about the tight bends in the piping, so if your are getting your Gauge feed from the IC piping maybe its blocked and backing up before it gets to the manifold.

Does the car go like shit off a slippery shovel when on boost or is it unresponsive and....well...slow?

GT

my old post for your same issue may help, the problem would come and go for me but in the end with the stock 25 in it, it was the intercooler piping causing my issue.

maybe you are special like i was, the previous motor in it was meant to be a 25 until it went bang and when i pulled it down found it had 26 internals with massive cams hence the too munch exhaust flow out of a stock 25 turbo. id be hoping to be special :cool:

http://www.skylinesaustralia.com/forums/in...=133869&hl=

13thracer thanks for the link it got me thinking, went to the garage in anger determend not to sleep till I found the problem coz it just didn't add up.

Then it dawned on me that the idiot who assured me that the pod filter would flow more than enough air for my application may have been talking out of the wrong hole. Set the wastegate up as it should be,Yanked the poddy off and in a fit of foot stomping anger wheeled out of the garage, freaken thing is holding boost perfectly!!!

Somehow I new this problem was going to end up making me look like a total tool :( my experience with cars is that 90% of the time it's something simple.

Bad news is it probably doesnt have super awsome internals, damn it!

Thanks for all the advice guys

OK so i can't be bothered reading the post, drunk an all, but i had a problem with my stock turbo, in that it would bost creep, no matter what, so i took it off, and bored the gate out and the surrounding inlet, no more issues now. LOVE IT.

no dramas mate....

where abouts are you getting the reading for the boost gauge?

is it off the IC piping or the manifold?

was thinking along the lines of what has been said previously about the tight bends in the piping, so if your are getting your Gauge feed from the IC piping maybe its blocked and backing up before it gets to the manifold.

Does the car go like shit off a slippery shovel when on boost or is it unresponsive and....well...slow?

GT

Thanks brother it turned out to be the pod filter without it, it holds boost perfectly... I still would have expected different symptoms but I guess if your not learning then your probably dead!

The guy that sold me the filter(and specifically assured me it would flow enough) is going to get a kick in the nads. :(

Cheers for your time

The pod filter wouldn't cause your boost to go up to infiniti. Something is at play here.

With my stock turbo, it held boost perfectly. I had all of the usual gay stuff like ic, exhaust, pod, blah blah blah.

With just the actuator connected, it would hold 5 psi. with the normal dual boost thing, it woudl do about 9 psi after all those other mods. never higher.

Somethign is definitely at play there. It's impossible if the flapper is wired open for it to still go to crazy boost. If you knwo someone that knows a bit about turbos, get them to take a look at it.

A pod won't do shit in terms of affecting boost.

out of interest does the pod have the top of it sort of blanked off (no air goes in the top just the sides) like you i had pod issues too with the crapy K&N have a look at the apexi power intake take a good look at the diagram on the box or on the web, of how the air enters the pod and how it goes into the AFM it creats less turbulance with air flow. i noticed it drove and went smoother after fitting a apexi than the K&N which when in comparison was just nasty, try a power intake and you will be pleasatly suprised.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Well, I can recommend the partial AV system translation CD I ordered from Car Audio Workshop in NZ. Whilst it didn't address the date issue, it has conveniently translated on-screen menu items into English, and now allows the GPS-received time to be offset in hours rather than minutes, so I can display Eastern Australian time accurately ( and bump it by another hour when daylight savings starts ).
    • Yuh, if it's 45°C outside, my car is driving in it.
    • I'd be curious to hear more. Otherwise, have you driven a modern x-trail? I wonder how it compares. Here in Australia they are/were popular for rentals and fleet vehicles. I have been in some and my impression was they are bad. But, this may have been very different in the 2000s at a good trim level. Twenty years is plenty of time to make the model worse. I do very much agree with the 2 silver cars in the garage approach. But, not driving because it's too hot would not leave a lot of time in the year for many Australians. I don't think you need to worry too much unless the car has actual issues with overheating. 
    • Back again. I returned to Japan in Jul/Aug to spend time with the car on my birthday and remind myself what all the sacrifice and compromise is for. It happened to line up with the monthly morning meet in Okutama, which I have been wanting to go to for a long time. It's a unique event at a unique spot with really rare, interesting, and quirky cars. It's where all the oldheads and OGs gather. The nighttime scene at DKF certainly has its place and should be experienced if you're into cars, but there's too much bad attention and negativity around it now. IMO the better time is Sunday morning at DKF or Okutama; it's more chill and relaxed. I'm glad I was finally able to go, but not sure it's worth the drive from all the way from Nagoya immediately the day before, unless I was already staying in Tokyo for the days right before the meet, because you have to wake up quite early to make it in time. Funnily enough though I didn't drive the car all that much this trip because it was just too damn hot. While there were zero issues and running temps were nominal and the A/C was strong, RBs already run crazy hot as it is. Sure, it took it all like a champ but something about driving these cars in the ridiculous heat/humidity bothers me and makes me feel like I'm asking too much of it. I'm just me being weird and treating the car like a living thing with feelings; I'm mechanically sympathetic to a fault. Instead I was mainly driving something else around - a KX4(silver) 2001 X-Trail GT, that I acquired in May. There's a few different flavors to choose from with Xs, but visually it's the Nissan version of the Honda CR-V. Mechanically it's a whole different story as this, being the top-trim GT, has an SR20VET mated to a four-speed auto and full-time AWD! It was a very affordable buy in exceptional condition inside and out, with very low mileage...only 48k kms. Most likely it was owned by an older person who kept it garaged and well-maintained, so I'm really happy with how it all worked out. It literally needs zero attention at the moment, albeit except for some minor visual touch-ups. I wanted something quirky, interesting, and practical and for sure it handily delivers on all three of those aspects. I was immediately able to utilize the cargo and passenger capacity to its full extent. It's a lot of fun to drive and is quite punchy through 1st and 2nd. It's very unassuming -in the twisty bits it's a lot more composed than one would think at a glance- and it'll be even better once I get better tires on it(yes, it's an SUV but still a little boat-y for my liking). So...now I have two golden-era Nissans in silver. One sports car and one that does everything else; the perfect two-car solution I think👍 The rest of the trip...I was able to turn my stressed brain off and enjoy it, although I didn't quite get to do as much as I thought. I did some interesting things, met some interesting people, and happened into some interesting situations however, that's all for another post though only if people really want to know. Project-wise, I went back to Mine's again to discuss more plans and am hoping to wrap that up real soon; keep watching this space if that interests you. Additionally, while working in the tormenting sweatbox that is the warehouse, I was able to organize most of the myriad of parts that my friend is storing for me along with the cars, and the 34 has a nice little spot carved out for it: And since it can get so stupid hot in there, that made it all the more easy -after I was standing there looking at the car and said 'f**k it'- to finally remove all the damn gauges that have mostly been an eyesore all this time. Huzzah. The heat basically makes the adhesive backing on the gauge mounts more pliable to work with, so it was far less stressful getting this done. I didn't fully clean it up or chase the wiring though; that will happen once I have the car in closer possession. Another major reason to remove all that stuff is to give people less reasons to get in my car and steal s**t while it's being exported/imported when/if the time comes, which leads us to my next point... ...and that is even though it's time in Japan is technically almost up since it's a November car and the X would be coming in March, I'm still not entirely sure where my life and career is headed; I don't really know what the future looks like and where I'm going to end up. I feel there's a great deal of uncertainty with me and as a result of that, it feels like I'm at a crossroads moreso now than any point in my life thus far and there are some choices I need to make. Yes, I've had some years to consider things and prepare myself, however too much has happened in that time to maintain confidence and everything feels so up in the air; tenuous one might say. Simply put, there's just too much nonsense going on right now from multiple vectors. Admittedly, I'm struggling to stay in the game and keep my eyes on the prize. So much so in fact, that very recently I came the closest I ever have before to calling it quits outright; selling everything and moving on and not looking back. The astute among you will pick up on key subtext within this paragraph. In the meantime I've still managed to slowly acquire some final bits for the car, but it feels nice knowing there's not much left to get and I'm almost across that finish line; I have almost everything I'll ever want for my interpretation and expression on what it is I think an R34 should be. 'til later.
    • Thanks for that, hadn’t used my brain enough to think about that. 
×
×
  • Create New...