Jump to content
SAU Community

Recommended Posts

  • Replies 98
  • Created
  • Last Reply

Top Posters In This Topic

Think outside box alittle bit..

low fuel consumption from the engine, same fuel pressure and volume from the pump = most of the fuel is getting heated in the fuel rail and is then getting sent back to the tank (over pumped), recycled and pumped up again. On a nice cruise the fuel gets 'hot' and the problems unfold. Its not about the pump, more about the the flow rate and the engine just doesn't require that much fuel at very light throttle, so the fuel reg just bypasses it and sends it back.

a smaller pump would have less return flow, but wont have the flow for max engine output. that make sense?

Ok i fully understand the point, I just cant quite comprehend that out of all the 044's running externally in cars today that all these people are having to run a fuel cooling setup to solve the overheating problem?

That said im going to track down a oil cooler and do some mods to it and at least try that option.

Would people suggest mounting it in the boot and running a fan over it or mounting it somewhere under the car?

Edited by SirRacer

ahhhh ANOTHER one of my threads being raised from the dead...

I can tell you for sure that the issue does exist... There would be many people having the same issue that are not aware of their cars that they do not think its a problem and they just live with it...

I PM'd you my phone number.. call me tomorrow after 10pm and i will chat to you about it. You definaty need a fuel cooler OR a voltage droppage configuration that will drop the pump flow on low rpm cruise loads.

On the subject of suitable coolers;

I have a just jap oil cooler core (30 row I think, its massive). I'm not going to use this for engine oil as I now want to get a genuine oil cooler kit for peace of mind. Would this be suitable to use as a fuel cooler?

Or, would it be ok to get a second hand tranny cooler and use that?

something like this: http://cgi.ebay.com.au/Oil-transmission-co...A1%7C240%3A1318

My plan is to mount it across the spare wheel well, with a thermo ontop next to my surge tank. Because the core is so large, will it have any problems pumping the fuel through the core and up into the surge tank?

Edited by gibbau
On the subject of suitable coolers;

I have a just jap oil cooler core (30 row I think, its massive). I'm not going to use this for engine oil as I now want to get a genuine oil cooler kit for peace of mind. Would this be suitable to use as a fuel cooler?

Or, would it be ok to get a second hand tranny cooler and use that?

something like this: http://cgi.ebay.com.au/Oil-transmission-co...A1%7C240%3A1318

My plan is to mount it across the spare wheel well, with a thermo ontop next to my surge tank. Because the core is so large, will it have any problems pumping the fuel through the core and up into the surge tank?

hey bud

that oil cooler you linked to ebay will be PERFECT for the job.. the just jap oil coolers aint too bad ... i use one.. you just need to make sure they dont leak and sometimes you need to mod them.. in my case i just got the fittings put into a lave and removed the ring for the o-ring and replaced them with a copper washer.. NEVER leaked again and it works a treat!!!

get tha oil cooler from ebay and use that as a fuel cooler, its much bigger then mine was and it will work great! i promise you this... use your just jap cooler as they aint too bad as long as they dont leak, if it does leak then DONT replace it just fix the leak.. then they work pretty damn good!

Good luck with it.

hey bud

that oil cooler you linked to ebay will be PERFECT for the job.. the just jap oil coolers aint too bad ... i use one.. you just need to make sure they dont leak and sometimes you need to mod them.. in my case i just got the fittings put into a lave and removed the ring for the o-ring and replaced them with a copper washer.. NEVER leaked again and it works a treat!!!

get tha oil cooler from ebay and use that as a fuel cooler, its much bigger then mine was and it will work great! i promise you this... use your just jap cooler as they aint too bad as long as they dont leak, if it does leak then DONT replace it just fix the leak.. then they work pretty damn good!

Good luck with it.

Thanks for your input :worship: I've just heard way too many stories about leaking lines destroying engines and whatnot from china kits.

I'm a fitter and turner apprentice so it's no drama to mod the o-ring.

I'll give it a go and keep an eye on it

Hi all , I just read through this whole thread and a possibly silly idea occured to me .

Some late model cars don't have a return line from the engines fuel rail at all and I had to ask a long time mechanic mate of mine how such a system could possibly work .

He claims that they do actually have a pressure regulator and return but its close to the pump so possibly in tank ?

So me thinks what would happe on a conventional fuel injected car like an RB powered Skyline if the fuel pressure regulator was moved to a "T" piece a little short of the rail itself .

My thinking is that the heat is conducted from the manifold to the rail (or hot ngine bay) so if you could have a return supply system with one side of the T heading to the rail and no rail return do you get around the thermal issues .

The unknown is how hot would the fuel in the rail itself gets and what if anything the manufacturers do to get around it if it is a problem .

One things for sure , if in a hot state you stood on it the supply of fuel comming down the line should be cool once that in the rail had been used .

If this system is workable it should be reasonably cheap as all you'd be doing is moving the reg and adding a T piece and short runs of new EFI hose .

Thoughts ?

Cheers A .

i mounted my fuel cooler back in the car today. in a different spot so i can run a air con condensor fan as well.

will connect it back up to the fuel system next week, it just needs to be connected all the fuel lines have been run etc etc

The simplest way would be to reinvoke the factory system of lowering the pump voltage when not needed... this is obviously one of the reasons the factory do it in the first place, and we all go and rip it off. So way not use a spare output to controll your own setup of a relay and resistor. You could experiment with what size resistor will maintain the flow needed below your chosen rpm (since bosch flows more, it may need less volts at low revs than the stock pump needes to maintain pressure) ...

A correctly working two stage system is the best soloution , no coolers required.

Gary

my car also had these issues running twin external 044s and 2 in tank pumps feeding the surge tank. Not too noisy until about 45 min into a drive on a hotday and the 044s would whine like crazy until it cooled down and then they are fine again. Im gonna look into the fuel cooler setups now, just wondering what sort of dimensions are these coolers u guys are using?

my car also had these issues running twin external 044s and 2 in tank pumps feeding the surge tank. Not too noisy until about 45 min into a drive on a hotday and the 044s would whine like crazy until it cooled down and then they are fine again. Im gonna look into the fuel cooler setups now, just wondering what sort of dimensions are these coolers u guys are using?

i just used a small tranny oil cooler, its not very big but it does help the system go 3 times longer before the pump starts to complain.

For the record, my 040 intank has done the same.... noisy as hell after a dyno session and slow drive home..... its been quiet when cool. i guess since its submerged its cooled for longer, however the dyno session heated up the fuel alot .

I'll wire the two stage back in, modified of course to provide full power when switched to direct.

Gary

so whats the benifits between using an ally oil cooler or proper copper fuel cooler or tranny cooler? any differences? i assume the fuel cooler is made for the high pressure side, they look like a copper tube in an S shape and fins around them. Ive even considered the moroso fuel cooler setup as well, but they are pricey compared to other options.

Have you heard of this sort of issue being common? Spoke to a Race Car builder yesterday who says he hasnt come across this problem at all when building RB powered cars. Another two mates have 044 powered setups running exactly the same system as me with no problems at all. All rail fuel was being returned back into the surge tank.

I wonder if its just the way the fuel lines are run or something in the RB's?

if you wire the 2 stage back in, will it be enough power to run 2 x high pressure pumps?

Obviously not the std setup, but a custom setup would work fine. I'm about to swap out the 040 for a walbro over the chrissy break, so i will have a look at the wiring and work out a way to wire an external two stage setup triggering off the stock one and get back to you , with a drawing and all if anyone is keen.

Obviously i can't say definitively what voltage the "low" setting has to be, until i get an idea what each pump needs to work at minium load setting, then i can reccomend a resistor to suit.

I'll come back with some definate info later on. And if there is interest i can whip them up to ease install for those not into electronics/ electrical etc .

Gary

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I have been being VERY quiet about what you're alluding to, as it is something that ticks me off... The number of cars from factory that run coil overs is HUGE! Most of them these days do... The other part that annoys me, is people saying "Well all the incabin adjustable suspension is illegal by blah blah blah"... If that's the case, then why can I buy a car brand new that can do it if, FULL STOP in cabin adjustable suspension is illegal...   Also, I could just chuck some aftermarket shocks in my car, throw the stock springs on, after my blue slip, dump my super low springs back in. Same shock and spring style setup... Hell, they could also be the same colour springs etc.     I'm voting, BlueSlipper didn't want to touch the above car for some reason. Whether it be some sort of bias against the car, the owner, them maybe having previously done dodgy shit and now they're being super careful in case they get slapped in the face by the Gumbyment again... Find a new blueslip place.   And can confirm as you had said, yes there are holy bibles of vehicle heights, and all sorts of other suspension stuff. Heck your run of the mill mechanic, and tyre shop has access to all of that stuff. It's how they do wheel alignments...
    • Funny story Heading to Sydney this morning on the HWY there was some slow traffic, so I gave it the beans and midway through my overtaking "power run" I lost all power It seems that I missed a hose clamp,  and the MAF and filter went WiFi To make this more problematic, the little tool kit that lives in the boot, is sitting in the sun room at Goulburn......LOL Luckily for me I found a bit of steel on the side of the road that could be used like a rusty and bent flat head screw driver to tighten it up enough that it got me into Sydney, it is now all tight like a tiger with the aid of a 8mm socket Note to self: Use my brain and double check stuff, and always keep that little tool kit in the car for when I have a brain fart
    • Oh, and as for everyone with their fuel economy changes, I switch between E10 and 98 in the company car. Even do when I had personal cars that could run on E10. You know what changed my fuel economy in any noticeable way? How I drove, and where I drove. Otherwise, say on full tanks of just back and forth from work only (So same trips, same sort of traffic), couldn't notice a difference that I can correlate to the type of fuel in use. In the current vehicle, that's over 42L of USABLE fuel. While 98 is all "more energy dense", it also has higher knock resistance as it takes more energy to get it to ignite too. The longer hydrocarbons, typically more tightly bound. So running the same ignition map, can also produce less power, if there isn't enough time to get it all burnt through properly, as yep, the flame propagation speed is different from lower octane fuel to higher (Higher has a lower flame propagation, due to the more tightly bound and harder to self ignite funs. This is also typically where, a vehicle that is designed purely to run on 91 (Whether it be E10 or normal 91) usually sees absolutely no real world difference in fuel economy for the normal man, woman, or dog.
    • We've got some servos around me that have 91 with E10, 91 (no E10), 95, and 98. At those stations the change from 91 E10 to 91, is typically around 8c/L.   But lets not get started on the price of fuel in Oz. It's ridiculous. All the service stations around me, bar one, the price of fuel has been over the $2 mark per litre for the cheapest, 98 being around $2.45. That one service station is a CostCo, fuel from it comes from the same refineries, and makes no pitstops, it runs great, including the 98. In fact, I've had no issues on CostCo fuel, but plenty of issues at other stations!. The CostCo fuel, was $1.65 roughly this week for 94 with E10. $1.88 for 98. Servos directly across from it, $2.10 for 91 E10, and $2.48 for 98. The part I had to laugh at? If I drive multiple HOURS away from Brisbane, say out near Nanango, or Kingaroy, or even out to Goondiwindi, the price of their fuel, is the same as what it is at the CostCo... Oh, and that BP servo at Goondiwindi is HUGE and goes through epic turnover of fuel, so it's not sitting there for weeks going to shit. And what blows me away, my mate is one of the people who drives the Fuel Tanker all around QLD, delivering to all those places. At the same company his previous role was doing the "local haul" deliveries... Same truck, same driver, same pickup point it all comes from. So you tell me, how the hell it is 60c/L CHEAPER for fuel, when nearly all else is equal, except they require a B-Double to drive half a day out of Brisbane, and half a day back, every second day, compared to the delivery that can be under 30 minutes drive from the fuel pickup point... Not to mention, go five blocks down the road, and Ampol to Ampol will vary 30c/L... And I've had this conversation with my mate... The way it's priced, is just typical, pure and utter rubbish... He also does runs from Brisbane, to all over QLD, down to Newcastle, Sydney, Nowra, Melbourne, Geelong, and even out to parts of the NT depending on the companies needs. His main stuff is all the longer distance away from home for a few days at a time, then when he's back, he loves to just pickup extra shifts wherever he can in whichever truck, hence all the weird different places.   Oh, as for getting E10 into all the fuels in Australia... It was very quickly highlighted, that we don't have enough biomass available to use to make E10 sustainably like they require, and it would dramatically cut into our, and the worlds food chain supply...   I vote we all just start running on liquid methane gas... Plenty of that just getting tapped off at tips from underground decay... (Note, this is pure just stupid commenting. I could very easily highlight the reasons its not a good idea especially on scale...)
    • Am I correct in assuming that the R35's are getting the classic skyline haircut off the odometer?  Quick search on carsales, there are 33 08 and 09 GTR's for sale, only 2 of them have more then 100,000km's on them (116,075 and 110,000 respectively).  And somehow there are about 25 for sale with around 60,000kms? Looks like the classic skyline haircut to me =/
×
×
  • Create New...