Jump to content
SAU Community

Recommended Posts

buy my ones if thats what you looking for, they are ok just need paint job and bit of fiberglass and presto you got your self wide body like a GTR, u can have them for $150

ow they are off my R32 didn't want them as i put genuine GTR panels

post-35658-1178093195.jpg

Edited by BRUNSKIGTST
Link to comment
https://www.sau.com.au/forums/topic/166921-bn-widebody-kit/#findComment-3092066
Share on other sites

buy my ones if thats what you looking for, they are ok just need paint job and bit of fiberglass and presto you got your self wide body like a GTR, u can have them for $150

ow they are off my R32 didn't want them as i put genuine GTR panels

already have fibreglass copies of the r32gtr guards... thanks 4 the offer

Link to comment
https://www.sau.com.au/forums/topic/166921-bn-widebody-kit/#findComment-3095039
Share on other sites

hmm... guess you should ring Driftline in melbourne... 0425855540 or www.driftline.com.au

they've fitted a couple of copies of my 9 piece BN blister kit now :) my original's still in the shop... I'll fit it to my car one of these days.

BTW, if its less than a 50mm extension, its not a widebody, its a fender flare :P

Link to comment
https://www.sau.com.au/forums/topic/166921-bn-widebody-kit/#findComment-3095085
Share on other sites

Hey guys im also looking to buy this kit , Its a Bn sports blister kit. There was a short write up about it in a recent Drift Battle mag, They claim that jetspeed sell them, but after various phone calls, they dont know wat im talking about.

Any help would be great. here are some pics.

post-22171-1178191634.jpgpost-22171-1178191643.jpg

cheers Tim.

Edited by vsute
Link to comment
https://www.sau.com.au/forums/topic/166921-bn-widebody-kit/#findComment-3095801
Share on other sites

yer i sued the guy who fitted the last kit didnt mould the rear gurard properly, and they started to crack,

the dickhead isnt paying up so, so i will be lucky to get my car back at the end of the year.

so im trying to source a rolling shell so i can get it back on the road

Link to comment
https://www.sau.com.au/forums/topic/166921-bn-widebody-kit/#findComment-3099560
Share on other sites

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Have you done the Ignition Sync Wizard in the AEM software?
    • Find out what RPM it was idling at with the IACV unplugged. It's very weird that the rpm didn't change at all, and then it stalled. When it stalls is it nearly like a switch off, like you've turned the engine off? Or is it more stutters and sputters and coughs to death over a few seconds? Or does the RPM just slowly keep going down and down? Have you done a test of trying to start it with the AFM unplugged? Does it still die?     If you Follow Josh's advice on using Nistune to check the voltages (which is a perfect method!) if you see anything out of wack voltage wise, THEN get the multimeter out and read the voltage directly at the sensor. If the two vary, then you're now looking for a wiring issue vs a sensor issue. So be aware, what the ECU sees, may not be what the sensor is actually saying too...
    • You very likely need to get it on a dyno and tune it. My assumption is, you've got an RB25DET tune in it, which has a different manifold, different injectors, and different cams as a minimum. What O2 sensor are you running?   When you say it runs extremely rich from idle all the way to redline, is this just free revving it you see that?
    • I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
    • I don't know any details, but I really wouldn't be surprised if they do it as a LHD only version, at least initially.
×
×
  • Create New...