Jump to content
SAU Community

R32 Gtr Wrecking And Other Stuff

GTRGTR
 Share

Recommended Posts

GTRGTR Rising Star

GTRGTR

Posted
Posted (edited)

HI ALL

I HAVE THE FOLLOWING PARTS AVAILABLE OFF AN R32 GTR. ALL PARTS ARE IN TOP CONDITION UNLESS OTHERWISE MENTIONED.

MORE PARTS THAT BECOME AVAILABLE WILL BE LISTED WHEN THEY ARE TAKEN OFF THE CAR.

ALL PARTS ARE LOCATED IN SYDNEY SO PICKUP IS WELCOME.

BELOW IS A LIST OF PARTS WITH "PICKUP ONLY" PRICES. DELIVERY PRICE WILLL BE SHOWN WITH (+$...) AFTER THE PICKUP PRICES.

IF U REQUIRE A PHOTO OF A PARTICULAR PART PM ME AND ILL SEND ONE THROUGH

REMEMBER NEW PARTS WILL BE ADDED SOON AND REGULARY SO CHECK BACK

CHRIS

................................................................................

..................................................................

ULTRA TURBO TIMER WITH HARNESS OFF 32GTR $20 (+$5)

BRAND NEW IN BOX, LIQUID FILLED AUTOMETER OILPRESSURE GAUGE WITH BLACK AUTOMETER MOUNTING CUP: SOLD

REAR SEAT SETUP: SOLD

SILVER BOOT LID WITH GENUINE N1 LIP AND GTR BADGE, FACTORY WING HOLES PROFESSIONALLY REMOVED: $400 (+WILL QUOTE TO SEND)

ELECTRIC SIDE MIRRORS SILVER. FADED IN NEED OF SPRAY, PAIR: $150 (+$20)

REAR LIGHTS. IN SILVER. PAIR: $200 (+$25)

FRONT INTERIOR LIGHT: $25 (+$5)

REAR INTERIOR LIGHT: $25 (+$5)

REAR VISION MIRROR WITH SCREW MISSING TO TIGHTEN ANGLE: $20 ($5)

FLOOR CARPET, NO BURNS OR RIPS, VERY VERY SLIGHT DRIVER FOOT WEAR: $80 (+$20)

REAR PARCEL TRAY CARPET WITH PAIR OF INFINITY TWEETERS: $30 (+$10)

ROOF LINING NO SAGGY SPOTS:SOLD

DASH WITH NO VENTS. 2 VERY SMALL SCREW HOLES FROM GAUGE:SOLD

NISMO FRONT STRUT BRACE BAR (GENUINE NISMO PRODUCT): $100 (+$20)

FRONT WINDSCREEN DEMISTER VENT: $45 (+$10)

TOP SECRET GEAR KNOB, SLIGHTLY AGED WITH 5SPD PATTERN: $30 (+$5)

HANDBRAKE: $45 (+$10)

REAR WINDSCREEN WIPER MOTOR: $35 (+$5)

LOWER FRONT LIP. SLIGHT DAMAGE. IF INTERESTED WILL SEND PIC: $125 (+WILL QUOTE TO SEND)

A/C CONTROL CLUSTER: $70 (+$10)

CENTRE GAUGE CLUSTER: $70 (+$10)

FRONT DRIVE SHAFT FROM GEARBOX TO FRONT DIFF: $80 (+$20)

REAR BRAKE CALIPERS: $200 (+$25)

CENTRE CONSOLE WITH LID AND HANDBRAKE SURROUND:SOLD

Edited by GTRGTR
Link to comment
https://www.sau.com.au/forums/topic/167095-r32-gtr-wrecking-and-other-stuff/
Share on other sites
UnknownWarrior Newbie

UnknownWarrior

Posted
Posted

I'm wondering if the Gtr front lower lip will fit under my standard GTS4 front bumper?

does anyone know?

If you could measure the dimensions of the lip that would be great!

I could pick it up in sydney easily!

GTRGTR Rising Star

GTRGTR

Posted
  • Author
Posted
I'm wondering if the Gtr front lower lip will fit under my standard GTS4 front bumper?

does anyone know?

If you could measure the dimensions of the lip that would be great!

I could pick it up in sydney easily!

have seen on gts 4 before. not to sure if modifications were made.

no floor mats all pms answered to!!

shunter Apprentice

shunter

Posted
Posted

hey mate, i'm after the injector and air flow metwer harness and also the fuel tank cover ( need the fuel level sender and floats but i know it's just one unit),. what u asking for them???

GTRGTR Rising Star

GTRGTR

Posted
  • Author
Posted
hey mate, i'm after the injector and air flow metwer harness and also the fuel tank cover ( need the fuel level sender and floats but i know it's just one unit),. what u asking for them???

all pms answered

robbieraver Rising Star

robbieraver

Posted
Posted (edited)

hey dude do you have the plastic centre console that goes around the air con sterio and dials.

also the plastic that goes around the gear boot, it holds the gear boot in placce.

both in black.

also the braking ducts that go underneath the lower lip.

thanks.

Edited by robbieraver
GTRGTR Rising Star

GTRGTR

Posted
  • Author
Posted
hey dude do you have the plastic centre console that goes around the air con sterio and dials.

also the plastic that goes around the gear boot, it holds the gear boot in placce.

both in black.

also the braking ducts that go underneath the lower lip.

thanks.

sent u a pm

Guest
This topic is now closed to further replies.
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Gareth87
      What should I do next to hold the head on

      By Gareth87 · Posted

      I can see between the water jacket and cyl 3 there wasn't a hard line of combustion gas. It certainly appears that the issue is coming from there. Yes, checked the tension. All at 100ft lbs where I set them 5 years ago. These blocks can crack but generally when they have been over bored. Mine is only 0.5mm oversize at 89.5mm. They break between cylinders around the 91mm mark. No sign of that with mine. My gut feeling is the head gasket lifted a while back when the studs stretched and i bandaided it by retorquing the studs. It's finally let go.
    • TurboTapin
      new 1.5 LSD issues/concerns

      By TurboTapin · Posted

      My Nismo 1.5 churps a bit on reverse turns when cold, but besides that feels like a stock diff.
    • The Bogan
      NC MX5

      By The Bogan · Posted

      Yes, but, I paid cash and I'm pretty sure the receipt was in the bin 10 minutes after I got home Note to self, keep all receipts
    • MBS206
      NC MX5

      By MBS206 · Posted

      Bunnings would have just handed you your money back on that one!
    • The Bogan
      NC MX5

      By The Bogan · Posted

      So, version 4 intake is on its way I was looking at these a while ago but at around $200 or more it was a little pricey for something that might not work, but, I had it in my watch list, but, I got a message saying it was on special, and I had a code thingie to use, it eventually came in at $120 delivered, so BAM, BUY NOW.....LOL I'll need to have a look when it arrives but I feel it will "look" better than what I currently have, as it comes with a PCV fitting, so I will be able to get rid of the alloy pipe that goes to the throttle body with the PCV fitting  Well, that's what the voices in my head are telling me  Oh, and this happened today Yeap, it was a Trojan, and it was cheap, so I headed back to the hardware store and actually spent a little bit more on a heavy duty,  one that was actually recommended by a plumber mate, a Cyclone one with a fibreglass handle that is actually rated for clay The broken shovel will eventually be "modified" into a short handle shovel
×
×
  • Create New...