Jump to content
SAU Community

Wanted To Trade - 2 X R33 Gtst 5 Speeds For High Hp Auto Setup

Guilt-Toy
 Share

Recommended Posts

Guilt-Toy Grand Master

Guilt-Toy

Posted
Posted (edited)

I am looking to trade the 2 R33 GTST Box's i have one in the car and one sitting at home for a Auto Setup that can handle at least 500hp at the rear wheels for a R33 Skyline.

I can also offer the pedals and master / slave and clutch lines to go with this if your interested and clutch / flywheel Exedy 5 puk.

Looking at something that is driveable on the street as well but aiming for low 10's on the track.

One box has 80,000kms and in EXCELENT condition which could sell for $1700 on its own and one has around 170,000 that needs the 4th gear syncro clip replaced (will be done prior to trading) so both box's in good or excelent working condition for trade.

I AM NOT INTERESTED IN SELLING a box yet unless you offer me 2k. Just EOI for trade at the moment please!!

Edited by Guilt-Toy
SECURITY Grand Master

SECURITY

Posted
Posted

hey champ,

i doubt anyone with a built auto will want to trade to manual, what i suggest doing is buying a standard auto box, selling your manuals and using the $$ to build your auto.

-standard autos have SEEN 320kw on standard internals, with just a valve body upgrade.

otherwise try convincing me to swap lol.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      boost source Size Garrett gt28 gen2

      By GTSBoy · Posted

      Totally equivalent. Stock often goes from the comp cover because that's where the actuator is also installed and the factory needs 2" of hose to make the connection - and it comes as a pre-assembled unit. They totally have a boost reference from somewhere between the turbo and the throttle(s). Oh, jeez. Just do it in M12 then. We don't actually care that much. I would expect any such AN converter fitting to rely on an o-ring or some other seal onto a flat surface under the flange of the hex**, because bolt threads are no intended to provide a pressure seal. unlike..... pipe threads. **which also requires a suitably flat and smooth surface on the turbo's boss to provide the seal.
    • timmy94
      boost source Size Garrett gt28 gen2

      By timmy94 · Posted

      I also used NP   That’s were it’s seems to be the best place to fit it? All schematic shows also that it’s should be referenced from the turbo housing. But idk, I do see high hp cars without any connection or anything to their turbos, so I really don’t know how they connect their things
    • timmy94
      boost source Size Garrett gt28 gen2

      By timmy94 · Posted

      I do have loctite 243 and 246 and a few more models. I could drill it now in place and make new threads for m12 and order an4 - m12 coupling and fit that to the turbo. Run a braided hose to the EBC which I could get a an4 to 1/8npt 
    • timmy94
      boost source Size Garrett gt28 gen2

      By timmy94 · Posted

      So M12 and sealant should be fine?    NPT ” because that’s what I had and what I could get atm. 
    • r32-25t
      R32 gtr transmission strength, billet plate

      By r32-25t · Posted

      Wouldn’t touch par if they gave it to me. You need to ask how much power you’re looking to make and then add about 50% to it because that’s what you’ll end up making  The factory box says no more at about 350kw or so, the upgraded synchro boxes won’t handle much over 500kw for long and at that point you’re looking at an auto or dog engagement manual,  once you’ve gone dog engagement you may as well go sequential, they cost a little bit more but it’s worth it  also while you’re at it you should upgrade the transfer case with 10 friction plates 
×
×
  • Create New...