Jump to content
SAU Community

1994 R32 Gtr 9,500 As Is. [south Australia]

Gold_32
 Share

Recommended Posts

Gold_32 Apprentice

Gold_32

Posted
  • Author
Posted
I don't know what the go is down in SA. Has it been complied and then failed by regency? If so who did compliance/when?

I am not too sure but from memory but i will speak to the guy i imported it with. its been sitting around for so long now i hevent wanted to deal or hear with it, but will get back to you about what happened.

There is no damage at all. Come have a looka t it if you are serious please.

R34_T88_Widebody Rising Star

R34_T88_Widebody

Posted
Posted

PM sent - also, have a few questions....

do you have original import pictures to show car with GTST wheels and black front bar? just curious as to why a car would go through a Jap auction or a yard in this state - normally they are the risky discards ( Grade X or Grade ***) that sell cheap for a good reason.....

Why were turbos removed? Why was exhaust removed? And - more importantly - why did whomever removed these not see fit to reinstall them?

If this car has failed compliance, then my understanding is that evidence needs to be supplied via the RAWS workshop back to DOTARS that the vehicle has been destroyed. at least this was the requirement a couple of years back. not sure what the full legalities are around this, but I suspect that it cannot even be used for a track car (which I am looking for), simply because it must be crushed. I believe that you can remove parts however. assume you can also sell it to someone to do the same....

cheers,

Jez

Gold_32 Apprentice

Gold_32

Posted
  • Author
Posted

The GTR wheels were sold with a gtst owner, hence the gtst wheels on there, and same goes for the exhaust. The turbos were removed for inspection and there was an upgrade on the cards. But since i found out it could not be registered my interest fell rock bottom hence the lack of motivation to get the turbos back on.

PM replied to

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • TurboTapin
      R32 GTST - 600KW+ RB28/CD009 Build

      By TurboTapin · Posted

      Well, my new WMI system took much longer to finalize. I actually missed my dyno appointment last Friday and lost my 150$ deposit. I'll be going back in the next week or two.  To sum it up. I only kept the AEM tank from my old setup. I replaced the AEM pump with a higher flow/pressure ProMeth 30GPH pump. I also swapped over to a 6AN low pressure feed line to the pump from the tank. There's also a pressure switch you cannot see on the pump high pressure line.    This is feeding 6x 200CC direct port nozzles and 1x 500CC Pre Throttle body nozzle. All fittings are Swagelok, because well why not. I also have a 300PSI pressure sensor up front.    I now have my Haltech ECU controlling everything. I start my pump with a basic relay at 5PSI and deadhead it. I then PWM a 3000CC methanol Injector to control flow starting around 10psi. The pressure switch in the trunk, along with my tank level are safeties before I ever get to 10PSI, and then I use my pressure sensor upfront as a secondary safety to cut the WMI and corrections in case the injector blocks or a line ruptures.  Wish me luck on the dyno!    
    • TurboTapin
      Jacks that fit under GTR lips that can reach the subframe?

      By TurboTapin · Posted

      So, I'm back with bad news. There's no jack long enough on this planet that will reach the front subframe. If by some chance there is, it would weigh 200lb's.  I purchased a long reach jack... The damn thing weighted 120lb's and was massive. Didn't even come close, was still short at least a foot. It was a pain, but I brought it back. Next I decided HA! No problem, I'll get an Extra long reach jack. Well, I couldn't lift the box... It must have weighed 160LB's and luckily there was an open box in store. I took measurement and was still nowhere close.  Sadly I've lost hope and have accepted defeat. 
    • suko
      J50 clock date suddenly reset to January 1

      By suko · Posted

      Thanks for that tip, niZmO_Man. I think the battery is OK. It's quite a new one, but I'll check. Last time I needed a new battery, everything electronic was fine, except that there wasn't enough current to turn over the starter. I decided to order one of the partial AV system translation CDs from Car Audio Workshop in NZ. That might have some effect, or help me diagnose the date problem. 🤞
    • Dose Pipe Sutututu
      Chris' Toyota Mark ii JZX110

      By Dose Pipe Sutututu · Posted

      I suppose it was relatively stock too, the JZ motor handle most mods thrown at them without even breaking a sweat 
    • MBS206
      Starter motor replacment teeth count.

      By MBS206 · Posted

      I saw your intro update, are you sure you've actually had a starter motor failure? You mention it could be the alarm causing it. I'm assuming you've got a no start issue, but what are the exact symptoms, as there could be a few reasons it has stopped wanting to start.
×
×
  • Create New...