Jump to content
SAU Community

Recommended Posts

I noticed the other day when my speed got above about 130km/h my car developed a fairly high frequency vibration that you can actually hear as a low hum inside the cabin. Not nice or confidence inspiring.

The only recent changes since i noticed it have been an rb25 box and a 1 piece tail shaft and i've also installed some new steering rack bushes but am getting no feed back through the steering wheel so don't think thats it.

Anyway, prime suspect at this stage is the 1 piece shaft which will be coming out for a check.

A second thing i noticed when i got under the car for a look to make sure the weights hadn't come off was that the outer CV's on both drive shafts had a lot of play. Could this be the cause and it's just a bit of a fluke that it's happened now? I'll be getting them recoed anyway as it causes the car to bounce back and forth at slow speeds like it has excessive back lash (which it doesn't) and they'll break eventually with the near 300rwkw if left alone anyway.

Oh, and it's definitely speed and not rev related as i dipped the clutch to make sure when it happened.

Changed the gear box mount too as that wasn't too healthy to begin with, no effect, but the box doesn't bounce up and hit the tunnel on bumpy roads any more. :P

Has anyone had issues with the CV's before as it's not something i've seen in my browsing over the last few years?

Link to comment
https://www.sau.com.au/forums/topic/169417-driveline-vibration/
Share on other sites

Pulled the drive shafts this morning and dropped them in to be recoed. The bloke reckoned they were in pretty good nick for their age, through there was some discolouration in the outer on one side due to heat.

He asked if they had been clicking (they had) as there was some minor dimpling in the outer ring of the outer CVs. So the whole clicking diff thing can be put to bed once and for all when i get them back on the car (hopefully).

Stuck the car in gear and brought the drive line up to speed (seeing as the were no driveshafts). Vibration is still there though no where near as bad with no load (or maybe driveshafts to contribute?), so the prime suspect is still the tail shaft. that can come out tomorrow and get re balanced.

Edited by BHDave

Dave drop it back to fourth and see if its still there.

I had a box that would vibrate in fifth gear over 110km/h. Slight high frequency vibe that would wobble the center interior mirror so that everything looked slightly blurred. Couldn't really feel it.

Box eventually blew third gear dropped in another and no vibe.

Have you eliminated the possibility of tyre/rim damage causing and this?

Yeah, I've already swapped the rear wheels to test it, no change.

Thanks cubes, I had considered the possibility that it was the box, but didn't want to go there at this stage :wub: I tried both 4th and 5th the first time I noticed it and it didn't seem to make a difference.

Yes.. I too am interested in this as i have the same problem.. or perhaps is it just a skyline attribute?

It happens over about 110Km/h and is fine if there is more than about 15% - 20% throttle but bellow that it vibrates..

Edited by GTS4WD

its the tailshaft. getting the driveline angle corect is a pain. what you can do is shim up the geabox on its mount as high as it can go. and use "pinaples" in the rear cross member to tilt the front of the diff upward.

for refecance there needs to be no more than a 2 degree diferance in shaft angle between the diff and gearbox. the height can be off but the centrelines have to be within this tolerance.

Got new drive shafts in, measured up to check the tail shaft angles based on daves posts and found the nose of the diff needed to come down about 3 mm and it would be dead straight, box end was spot on. So made some spacers, chucked them in, no difference :thumbsup:

And my rear roll center adjusters are the wrong ones :D

And now i have to get back under the car to remove the tail shaft :)

The box is pointing straight at the diff, so the whole lot is square (to within a mm or 2). I bent my tunnel up for clearance when i was installing the box so it was sitting in the right spot. The yoke is parallel to the tail shaft which is parallel with the pinion. I don't particularly want to start messing with subframe angles just so i can get away with using a one piece shaft. I'll get the original 2 piece shaft modded before i go that far.

Anyway, i got back under and removed the shaft so it's going to have the balance looked at.

It's about 75mm dead32.

What it COULD be (as it was with mine) is just dodgy unis. We had the shaft rebalanced, did nothing. Moved the box up, did nothing. Changed the wheels, same deal did nothing. Put it on the dyno under some load got under it to check, was definately the shaft.

Went back to the place that did the shaft. They then all of a sudden 'worked out' that they put the cheap uni's in. Put in the better ones, haven't had a problem since. So if everything else is hunkydory, that could be it.

It's back on the car, the vibration has improved a bit, it's still there but nowhere near as bad as it was. Saturday morning i'll be back under the car with a set of calipers checking again to see if anything has changed.

I knew i should have stuck with a 2 piece.....

I'm still running with the uni joints themselfs. Obviously check everything else first. Or do what we did with mine, whack it on a dyno get under the car, see whats wobbleing.

Just a shame those thompson couplings arent mass production yet.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Waaay ahead of ya....(evil laugh!!) Will show the fitment and spec details later when it isnt as rainy !
    • Thanks Dose.....    I appreciate it!!
    • I'll probably be putting the shit box back on the dyno again soon, I want to dial in the closed loop boost control properly. I'll have a camera facing the car/motor for fun too. Just note, there are essentially 3x 10AN inlets going into the catch can and 1x going back to the intake pipe. Most of the time the catch can "return" to the sump actually is the crank case breather, pushing air out.
    • I have the R3C with a Nismo slave and by no means does it behave like a stocker, it ain’t THAT bad. On take off just give a bit more throttle than you would say a coppermix and it’s fine. It will not slip though.   
    • Okay. Final round of testing done. Got a friend to hook up a fancy scanner to the car and we also ran some compression and leakdown tests, she is healthy.  The MAF was definitely the culprit. So for future reference anyone with similar issues that find this thread. I suggest the following steps, in order of affordability:   Check your spark plugs for any fouling, replace plugs if they are bad or re adjust the gaps making it narrower (0.8mm would be good). Check every coil's resistance with a multimeter. It can be done by probing the IB and G pins on the coil pack. Resistance should be around 1.4 (+/- 0.1) Ohms Check the MAF. If you have Nissan connect or a good scanner with the 14 adapter it should allow you to see the voltage on the MAF reading should be around 1.1 - 1.2V when car is idling. But if you don't, buy a new MAF from Amazon and test, then return it. (For instance, I got a Chinese one for $40 that was reporting 1.3v on idle). If you still have scanner, you can run tests on the injectors to see if they are working, just remember to unplug the fuel pump fuse/relay and have no pressure on the line. Then listen for the noises that the injectors make. Clean/replace injectors as needed. Once you find the issue and fix, order thousands of dollars worth of OEM parts to refresh unrelated things (Optional)   PS: Thanks to the absolute legends of this forum for the responses and help to someone that went a bit over their head. (me)
×
×
  • Create New...