Jump to content
SAU Community

Recommended Posts

Hi all, ive finally decided to part with my baby or at least sell off all the parts for the "plan" to have a tuff gtr. over the years i have quite a bit collected so here goes. please do not pm me as i do not come online often. if you wish to contact me please email me at [email protected]. Please do not whinge on this thread about Joe Bloggs down the road is selling it cheaper. Should you wish to contact me please call on 0417755890 after 6pm. thanks

USED TOMEI FORGED CRANK, FULL COUNTERWEIGHT $3800

USED TOMEI 87MM FORGED PISTONS WITH COOLING CHANNEL NO RINGS $1550

USED HKS GT-SS TWIN TURBO KIT FOR RB26. EXCELLENT CONDITION. NO SHAFT PLAY WHATSOEVER. LIKE NEW WITH HKS STRENGTHENED ACTUATORS. DONE 3XXXKMS $2450

NEW TRUST GREDDY FUEL RAIL 11MM INCLUDES LITTLE BITS AND PIECES, $300

NEW REINIK (NOW KNOWN AS REIMAX) GROUP A OIL PUMP. THIS IS THE PUMP USED ON THE GROUP A GTR'S IN JAPAN. REINIK ARE RESPONSIBLE FOR THE 2.8L IN THE 400R $1100

USED NISMO WHITE CLUSTER SET INCLUDED ARE SPEEDO 320KM, TACHO 11000RPM, TORQUE, FUEL, WATER TEMP, OIL PRESSURE $900

USED ARC TWIN ENTRY INTERCOOLER, APPROX 70-80MM THICK $350

USED ARC REAR STABILIZER BAR 30MM $320

NEW WIDE FENDERS FOR BNR32 FRONT 30MM WIDER ON EACH SIDE. MADE IN JAPAN. STRAIGHT BOLT ON. MEETS UP WITH STANDARD BUMPER. UNPAINTED. $900

NEW STEP 3 22MM PIN H BEAM CONRODS, STEP 3 APEXI VMAX 22MM PIN 86.1MM PISTONS WITH RINGS AND PINS & APEXI VMAX CAMS IN/EX 260 11.2MM LIFT, APEXI VMAX LIFTERS $4500 THESE HAVE BEEN SOLD

USED TRUST OIL SUMP EXTENSION. WELDING ALREADY DONE. DOES NOT INCLUDE ACTUAL DIFF. $700

Im pretty sure i have other parts too, but i havent finished clearing out the garage. I'll post them as i find them.

post-1554-1181248237_thumb.jpg

post-1554-1181248387_thumb.jpg

post-1554-1181248450_thumb.jpg

post-1554-1181248842_thumb.jpg

post-1554-1181248901_thumb.jpg

post-1554-1181248980_thumb.jpg

post-1554-1181249101_thumb.jpg

post-1554-1181249310_thumb.jpg

post-1554-1187140090_thumb.jpg

post-1554-1187140117_thumb.jpg

post-1554-1187140146_thumb.jpg

post-1554-1187140202_thumb.jpg

Edited by AtomicBomberMan

They are some good prices for some serious gear some one that wants a tough GTR should snap some of this stuff up.Good luck with the sale mate.

Will you sepeate any of the Apexi parts?

hi, which particular parts are you interested in? please sms or call me 0417755890

wht11 i am happy to separate. please check your pm. if youre interested, please call on 0417755890

cheers

for those that have contacted me. i will be in cairns until wednesday. any equiries by phone or sms only 0417755890.

INTERCOOLER SOLD

can you pm me the specs on the apexi turbo's

turbos are rated to 340ps each. bolt straight on to standard manifolds. includes all stainless earls lines and fittings for installation. kit is brand new. gtr's are running 10's with these turbos.

turbos are rated to 340ps each. bolt straight on to standard manifolds. includes all stainless earls lines and fittings for installation. kit is brand new. gtr's are running 10's with these turbos.

What size is the compressor and turbine wheel? (even if u can just measure the bits u can see) A/R's? Let me know and I'll make a fair offer if they suit.

What size is the compressor and turbine wheel? (even if u can just measure the bits u can see) A/R's? Let me know and I'll make a fair offer if they suit.

sent you pm. please check. http://www.apexera.co.jp/carlife/pro_apexi...URBO_syogen.pdf

Where about in Brissi are you? Im keen on the arc cooler.

im located on the west side indooroopilly way. can meet up if needed.

cheers

  • 1 month later...

gauges are sold

oil pump sold

crank and intercooler people are stuffin me around

parts can be found on ebay with rb26 or gtr as keyword

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
    • I wanted to try and preserve the front bumper as long as possible, they're not cheap and are made to order in Japan. Taking inspiration from my previous K11 Micra build where I made an undertray for the Impul bumper, I did the same for this BN Sports bumper but a little slimmed down.  This time round I only made a 'skid plate' (if that's the correct wording/term) for just the bumper surface area, the Micra version covered the gap like an undertray. Starting off with a sheet of mild steel approx. 0.9mm thick 4ft x 2ft in size. I traced around the bumper, cut it out and cleaned the edges. Luckily I was able to get two halves from one piece of metal In the video I installed it as is, but I've since then I've removed it to spray and add a rubber edging trim. The rubber trim is suitable for 1-2mm and it's a really nice tight fit. The bolts had to be loosened due to the plates being too tight against the bumper, the trim wouldn't push on I used some stainless M6 flat headed bolts for a flusher finish (rather than hex heads poking down), I believe this style fastener is used for furniture too incase you struggle to source some. The corner's are a little wider, but this may be an advantage incase I get close to bumping it  The front grill got some attention, finally getting round to repairing it. Upon removal one fixing pulled itself out of the plastic frame, one side is M8 that fixes inside of the frame, where as the other side is M5. Not knowing I could get replacements, I cut down an M8 bolt, threaded it inside the frame along with a decent amount of JB Weld.  The mesh was replaced to match the bumper. One hole on the bonnet/hood had to be drilled out to 8mm to accommodate the new stud, once the glue had set it could be refitted. I think the reason the grill was double meshed was to hide the horn/bonnet latch (which makes sense) but I much prefer it matching the bumper Bumper refitted and it's looking much better IMO The Youtube video can be seen here: https://www.youtube.com/watch?v=bVZP35io9MA
×
×
  • Create New...