Jump to content
SAU Community

modify your front bar

Jet

By Jet,
in Engines & Forced Induction

 Share

Recommended Posts

Ronin 09 Grand Master

Ronin 09

Posted
Posted

Hey Al, i never got to check out your front bar properly after the tint day... after cutting the bumper support, have you noticed any structural stiffness reduction - ie do the ends bend more easily or does the front bar seem less rigid?

JimX Grand Master

JimX

Posted
Posted

You should be able to use the cut out bit as a source of plastic for a plastic welder to patch them up again. I've never seen one patched up, the couple I have seen with the front section removed just have some ugly square holes left over.

Also, where do you put your plate after you do this? I hate plates that are off to one side, reminds me of a bus or army vehicle or something. I'm thinking it would look ok if suspended from the top section of the front (low profile plate only). It would still interrupt air flow a bit, but not nearly as much as the whole crosspiece does.

Bo0sT_JuNkY Community Regular

Bo0sT_JuNkY

Posted
Posted

this is my front bar ,I had to lose the front bumper blinkers cause of the intercooler,so i wired the parkers up as blinkers and moded the headlamps to run parkers and headlights.The bumper was already damaged when i bought it(underneath) so i wasnt really fussed with spending money to plastic weld the gaps.So i just cut it out bigger so it didnt have any:)

Al Grand Master

Al

Posted
Posted
Originally posted by T0nyGTSt

Hey fairies...

See the pic below.

Personally I don't think I CBF doing it. Flows fine.

T.

Forgot to recheck this thread, sorry for the delay. Tonygtst why is MY pic (that i posted in another thread. months ago) of MY CAR labeled as 'ben_front"?????:D

Is side monted plates illegal, i have never been pulled up on it? I thought that if a bar does not have a dedicated spot (and mine now doesn't :)) that it is ok to mount on side as lonf as it is clearly visible.

Ronin 09: I personally have not seen/noticed a differance, as the support bars, that held the middle bar, are still there, on either side of the cut out.

I would think this mod is illegal, but may not be picked up as it looks factory. What mods are not legal now a days?

T0nyGTSt Grand Master

T0nyGTSt

Posted
Posted

Ben has a maroon 33 as well and wants to do the sex conversions... his will look like yours soon LOL

I'm running around with an IC still behind the stock M-Spec bar.

Nah NSW cops are just being arseholes. Heaps of 'em gave me the "Alfa 156 is ok as it's stock, yours is not stock".

T.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • silviaz
      Returning after a long time!

      By silviaz · Posted

      Yeahhhh, the costs have killed me. Spent more than the cost of an engine rebuild and it most mostly servicing and a tune lol.
    • MBS206
      Duncan's V37.......race car?

      By MBS206 · Posted

      I'm not 100% how the BMW racers do it, but I know from other brands like Merc, moving, and changing the coolers is one of the things. Like getting a transcooler out from infront of the radiator to out near a wheel arch. So some of the stuff you've got crammed in the middle front, spread it out and open up where you can in the bar to get more air in to the sides.
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      Small update for the day... Turns out the intercooler and engine coolant hose kits are anything but complete....I probably should have counted better but it only really covers about half the coolant hoses in the car, it really just covers the visible stuff and pretends everything else doesn't exist (turbo water feed and returns and also heat exchanger lines through the 2 pumps and cooler) .In any case, I'm happier to have half reliable hoses than none, but a bit of a disappointment. Anyway...finger click (and 5 hours).....hoses in place, lots of spring clamps replaced with screw clamps, and engine coolant is on the pressure tester for the night.   Incidentally, upsized header tank is an Inifiniti factory option....not sure I'll ever do prod car racing in this but at least it is legal.
    • GTSBoy
      GTX2867R GEN 2 NO OUTPUT FOR BOOST SOLENOID

      By GTSBoy · Posted

      Just weld it onto the hot pipe. If you want it right after the turbo, put it right after the turbo. Or rip the comp cover off and drill and tap a hole into it.
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      hahaha glad I can rely on you two to go on a spiral at the drop of a problem! Some quick answers....the ducting is excellent top bottom and sides....everything that gets in goes through the coolers (noting the oil cooler redirects it out again, fair call if it is cooling 120o+) and the heat exchanger for the intercooler also has some scoops to pick up more than it's fair share too. I can't see going down the water spray track....no bueno for formal racing and a big risk for long rally days if you run out (plus I'm not clear if it is allowed there either yet).   Frankly, it must be possible to reliably put 400kw through a standard front end, the BMWs do it so I just need to work it out....I'm starting with reducing blockages in the way and adding some coolant capacity with a bigger header tank, flushing rad and making sure it was filled/bled properly (I didn't do the last coolant change); also taken measurements incase next step is a bigger/higher capacity custom radiator
×
×
  • Create New...