Jump to content
SAU Community

Recommended Posts

For Sale:

1993 R33 GTS-T Series 1

Manual

77,000kms

Sunroof

Engine internals:

Aries Forged Pistons

Aries Molly Piston Rings & Bearings

Shock Pein RB25 Conrods

Crank x-rayed, Polished & Balanced

Head has stainless valves 30mm Exhaust 34.5mm inlet

Three angled, cut valve seats

Ported Polished, Flow tested & Manifold Matched for optimum flow

600hp rated copper head gasket

N1 Oil & Water pumps

New Timing belt & tensioners

Engine externals:

Detailed in Blue

6" Cold air induction system

Simota Heat shielded POD filter

Straight pipe from POD to Turbo (non restrictive)

Custom turbo setup high flowed T3 front VG30 rear housing

RB20 Wastegate actuator

Monster HYBRID FMIC & Piping

Polished throttle body

Turbosmart Super Sonic BOV

3" mandrel exhaust from turbo

3" high flow cat into 4" Apexi Canon

Exedy racing clutch & pressure plate

Lightened and balanced flywheel

Exterior:

400R front and rear body kit with GTR sides and spoiler

17" Import rims

Interior:

Apexi turbo timer

Four point alarm & immobiliser

Pioneer head unit

Blue neons front and rear floors

Female owner, i had it put on the dyno and it has 187.9kw on the standard 7psi, is all ready for an ECU, injectors, fuel pump etc to reach its true potential! All the hard work is done. I am only selling because I need a horse float.

$16,500ONO

blacky003.jpg

blacky002.jpg

blacky001-1.jpg

skyline003.jpg

skyline002.jpg

skyline001.jpg

hope i haven't forgotten anything!!

0418 178 295

Edited by r33skizza
  • 3 weeks later...
  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yes, I know🙄 but the sequential is not in my budget... don't want to reduce power neither, so looks like I'm stuck in the rabbit hole🤣
    • You’ll be very upset when you bust that too not to mention the gearing totally sucks. Don’t do it.
    • Is the panel filter one that is oiled? Have you ever cleaned or touched the AFM?
    • So.... the K&N air box thingo was too big, ended up gifting it to a mate, well, by gifting it he actually supplied food and beer at the pub,  which was nice, as it will not sit on a shelf in the garage for the next 10 years I did trim up some of the existing stuff to neaten it all up and gave it some wrinkle paint, unfortunately it currently has a used and abused mish mash of different types of hose clamps, 4 big fat T bolt type (shit), and a few normal clamps of vairing sizes and brands, but..... only until the 6 constant tension black worm clamps that I ordered from EFI solutions turn up next week Currently the current hose clamps are triggering me hard, LOL Is this the final version, probably not, I really want just 2 silicone pieces, a straight bit of silicone from the filter to the MAF is easy and will happen as soon as I head into Just Jap tomorrow, the problematic part is a 30° silicone bend from the MAF to the TB that I can connect the engine breather from the head, I found that there are bulk head fittings for boat bilge pumps that should work, but until I can get a 30° silicone bend the alloy pipe, and the 11ty thousand hose clamps, are there for the foreseeable future 4 hose clamps are golden, 6 are grudgingly acceptable, the 8 currently holding it all together is just taking the piss    I've also ordered 60 more retaining wall blocks for the front yard, I mis-gonculated the height that was required to get above the base of the Photinia's (red robin's) that are the hedge behind the front fence, currently it is 2 blocks high, and about 1/2 a block short, so going 3 blocks high will be above the base of the red robin's, and allow some room for mulch
×
×
  • Create New...