Jump to content
SAU Community

Rays Volk Te37 18 X 9.5 For R33 & R34 Gtr's

kitch15
 Share

Recommended Posts

kitch15 Collaborator

kitch15

Posted
Posted (edited)

RAYS ENGINEERING WHEELS - MODEL - VOLK RACING TE37.

Full set of 4 - 18 x 9.5 inch wheels with YOKOHAMA 235 x 40 x 18 tyres Fronts (70%tread) and Michelin Pilot 265 x 35 x 18's Rears (30-40% tread)

RIMS are in very good condition, 2 have minor gutter scrapes.

Offset +12 is to suit R33 and R34 GTR's

Pick Up in Melbourne. Wheels are in Melbourne. Can be sent interstate at buyer's expense.

$2600.00 - first to see will buy..

Info on this wheel :

Material is 6061 aircraft grade aluminum. This material is hot forged. 1st forging process is done with pressure of 5,000 kilograms per square centimeter. 2nd forging process is a slow process with 3,500 kilograms per square centimeter. The lip is also forged to 3,500 kilograms per square centimeter. This allows the wheel to have less material than other wheels, but have more strength and durability. The excess material is machined off (to tolerance of 1/100 of a millimeter). Powder coating and clear coating is done by a special proprietary process to ensure long lasting quality and durability

post-26639-1181734045_thumb.jpg

post-26639-1181734088_thumb.jpg

Edited by kitch15
Sol32 Community Regular

Sol32

Posted
Posted
Mate do you know if these wheels will fit on a r32 gtr v spec>>

cheers :thumbsup:

Relatively sure they will fit any R32 GTR but will stick out... will look tough as hell but may have clearance issues at full lock etc... I could be wrong however.

J-Boy Mentor

J-Boy

Posted
Posted

Running 235/40/18 front and 265/35/18 rear on a gtr is fine. The rolling diameter is about the same for these 2 sizes and doesn't really affect ATTESA. I'm using these sizes of dunlop dz02g semislicks on the circuit and never had a problem with my gtr32.

kitch15 Collaborator

kitch15

Posted
  • Author
Posted
Running 235/40/18 front and 265/35/18 rear on a gtr is fine. The rolling diameter is about the same for these 2 sizes and doesn't really affect ATTESA. I'm using these sizes of dunlop dz02g semislicks on the circuit and never had a problem with my gtr32.

Thats exactly right J-Boy. 265's on front would struggle in an R32, in terms of clearance. Hence the smaller tyre choice.

Have a genuine buyer looking at the wheels today, so most likely sold.....sorry guys.....if falls through, will let you know tomorrow, to other interested buyers...Cheers

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • The Bogan
      NC MX5

      By The Bogan · Posted

      After using a protractor for an actually accurate assessment of what is required,  and by NOT using my uncalibrated eyeball I worked out I need a 25° silicone bend from the TB ro the MAF, but, my choice was either a 30° or a 23° (23° is a weird spec), so I grabbed the 23° one from Raceworks I also grabbed 1mtr of 3" straight from Just Jap, I needed 350mm, but they only had 300mm, or 1mtr lengths....meh Also ordered a 1/2" hose bulkhead fitting from fleabay, this has a smoothish mushroom looking head (they are designed for below the water line of boats) that will fit inside the bend, the hose bit and threaded bit looks to long, but nothing that a hacksaw cannot fix if required, the hose will then just get jamed on the threaded bit up to the retaining nut Fingers crossed and the unsightly amount of hose clamps will be reduced down to 4 once all the parts arrive 
    • joshuaho96
      R34 25GT Engine Light 21

      By joshuaho96 · Posted

      Oil change does not trigger code 21. Code 21 is for coilpacks primary side connection. You can try to clear the code with a battery disconnect, hold down the brake pedal to drain capacitors through the brake lights with the ignition on for 10-15 seconds before you reconnect the battery. I have seen R35 coil conversion permanently cause this code with no ill effects so it might be the resistance it wants to see isn't quite right on one or more coilpacks. Could be inside the ECU, could be the harness, could be a coil. You can test it all if you want or just ignore until the car actually starts misfiring.
    • joshuaho96
      R32 GTS (RB20DE) Injectors Replacement

      By joshuaho96 · Posted

      I forgot you have a Nistune ECU. Use Nistune to do all the tests I mentioned instead of faffing with 30+ year old electrical connectors. You can read MAF volts off that too, there are reference values in the service manual to tell you roughly what it should be in different conditions.
    • GTSBoy
      R32 GTS (RB20DE) Injectors Replacement

      By GTSBoy · Posted

      No. I think it might be the AFM. Hence the use of the terms "swaptronics", which implies the use of swapping out electronics for the purpose of diagnosis. It's about the only way to prove that a small/niggling/whatever problem with an AFM or a CAS or similar is actually caused by that AFM/CAS/whatever. A known good item swapped in that still gives the same problem is likely to be caused somewhere else. They're all the same. Spraying AFMs with cleaner is an each way bet between cleaning it and f**king it.
    • codygrimm27
      Can you mount the ATTESA pump in other locations?

      By codygrimm27 · Posted

      Oh wow! This might actually work amazingly. Do you know the ratio of the diff? I was told the only thing you need to make sure of is if the front & rear diff ratios are the same. Ours is a 4.083 Thanks!
×
×
  • Create New...