Jump to content
SAU Community

Recommended Posts

- heater box for r32 x 1 - -$30 each

- powersteering resivoirs x 2 - $20 each

- hicas pump and lines - $30

- white pearl 32 sedan boot (no damage, but no wing) - $40

- white 32 sedan boot tiny dint at back with type m spoiler - $80

- 32 sedan headlining (non sunroof - will not fit a coupe) - $30

- front cloth seats from a r32 - $80 both

- front passenger seat velour r32 - $50 ono

- r32 dash in ok condition 1 circle mark, not lifting - $50

- white pearl r32 bonnet tiny dint at front just above where the headlight is - $80

- Maroon LHS r32 guard few dints (from half cut) $30

- White pearl and white front RHS guard both have damage $30 both

- Maroon r32 halfcut stripped good for a crashed car to repair

-

Will also sell all front panels above for $450 ono

- 2) r32 rb20 turbos, i would say both nee a rebuild $50 each

- 2) r32 wastegate acuators - $40 each

- 6 rb20 injectors $50

- r32 automatic transmission, was shifting fine when took out to convert to manual - $50

transmission also come with flywheel and stall convertor

- rear k frame from r32, no diff - $80 ono

- r32 veilside coupe rear bar - brand new never fitted - $200

- r32 gtst m-sport 20mm wide guards (brother bought this for his GTR and they are for a GTST) - $150

Also have many interior bits and other parts from a 32 sedan.

Plus many engine parts as well

Prices are negotiable and i need to get rid of this stuff

Pics will be up soon for a few items, anything else pm for pics ill post

Also i do not have dash vents

Link to comment
https://www.sau.com.au/forums/topic/173091-parts-clearance/
Share on other sites

  • Replies 49
  • Created
  • Last Reply

Top Posters In This Topic

Hi mate,

r32 gtst m-sport 20mm wide guards (brother bought this for his GTR and they are for a GTST) - $150

- what condition?

- $150 for both?

- location? if u not in Syd, are u willing to post?

- some pics would be good

Cheers

Edited by subie
Link to comment
https://www.sau.com.au/forums/topic/173091-parts-clearance/#findComment-3183471
Share on other sites

hitoriko PM sent

subie - yes its $150 for both and are in brand new condition...never fitted.

I might post ill have to get a quote and make sure i can pack them properly so they dont break

Ill get pics for you 2moro

Cheers

Link to comment
https://www.sau.com.au/forums/topic/173091-parts-clearance/#findComment-3183834
Share on other sites

Pics

Also have 32 coupe lights (both have broken outsides can be fixed) - $50 both ono

32 fuel tank $40

front cross member, hubs and some suspension parts (one stud is bent) - $150

32 4 door mud flaps (2 sets) $20 each set

post-23551-1182157357_thumb.jpg

post-23551-1182157488_thumb.jpg

post-23551-1182157601_thumb.jpg

post-23551-1182157707_thumb.jpg

post-23551-1182157855_thumb.jpg

post-23551-1182157962_thumb.jpg

post-23551-1182159528_thumb.jpg

post-23551-1182159732_thumb.jpg

post-23551-1182159835_thumb.jpg

post-23551-1182160228_thumb.jpg

post-23551-1182160451_thumb.jpg

post-23551-1182160552_thumb.jpg

post-23551-1182160752_thumb.jpg

post-23551-1182160909_thumb.jpg

post-23551-1182161052_thumb.jpg

post-23551-1182161153_thumb.jpg

post-23551-1182161287_thumb.jpg

post-23551-1182161377_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/173091-parts-clearance/#findComment-3185953
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • You very likely need to get it on a dyno and tune it. My assumption is, you've got an RB25DET tune in it, which has a different manifold, different injectors, and different cams as a minimum. What O2 sensor are you running?   When you say it runs extremely rich from idle all the way to redline, is this just free revving it you see that?
    • I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
    • I don't know any details, but I really wouldn't be surprised if they do it as a LHD only version, at least initially.
    • Thanks for the replies everyone. Definitely a coolant push. Oil catch can is empty and always has been. As the engine is out now I'll be having a good look over things. I do have some detonation on the piston tops from a trigger issue back about 5 years ago. I felt it and shut off then bought a new ecu and changed the trigger. Never been an issue since. It never hurt the power, its made almost 80hp more since that incident but I will pull the bearing caps to take a look. If the bearings are damaged I will do a bottom end refresh. Head is being re conditioned at the moment and the block will be cleaned and checked to ensure it's flat. I'll go with a kameari gasket and see how it ends up. The other thing I'm not super keen on is the cylinder colours. I suspect this is from the inlet manifold. The plan will be to put it back together, retune and then stick a plazmaman billet inlet on it and retune. I'm happy with the power, if it makes a little more, then great, but I would rather just make everything more efficient at this stage.
    • Maybe they'll look to do a bunch of presales to help inject some cash fast for their financial issues...
×
×
  • Create New...