Jump to content
SAU Community

Recommended Posts

Hey all, getting a front mount kit for my r33 and after some advice/knowledge. The pipe my bov is currently on shown in picture is going to be replaced. The other pic shows the kit I am getting, or similar so where is the best place to now put my bov? Would it be better to leave the standard one connected (metal plate blocks the bottom where it joins the intake to stop it functioning) and just get a new adaptor welded to the new pipe if so should I completely disconnect the stock bov or is the plate sufficient enough. Or should just get an adaptor to suit standard position. My main concern is what do I do with the vaccum lines left over if I move the bov and disconnect stock one. I will have the plumback pipe sitting there for the stock bov and the line that connects the the blitz one left doing nothing. I dont know where they should be going if I move the bov, as it was already the way it is when I got the car. If you can get ya head around what I just said help me out please. I tried to describe it as best as I can. Thanks

If you can help me out add me to msn. [email protected]

post-38045-1182154480_thumb.jpg

post-38045-1182154528_thumb.jpg

Edited by Jamie88
Link to comment
https://www.sau.com.au/forums/topic/173262-front-mountblow-off-valve-question/
Share on other sites

yeh where it is now is prob the best place and the only pipe that should be left free if u have a atmos BOV is the plumb back pipe and that just simply has to be covered up... use a grommet or sumthing...

Edited by blinko
yeh where it is now is prob the best place and the only pipe that should be left free if u have a atmos BOV is the plumb back pipe and that just simply has to be covered up... use a grommet or sumthing...

Yeah but what im saying is when I get my front mount, the pipe its on now will be replaced should I get it put back on that new pipe. Or put it in the standard position where the standard bov still remains? If I put it on the new cooler pipe should I leave the standard blow off valve the way it is? It has a metal plate between it and the inlet pipe.

unless there is more piping for your fmic kit that what is show, you won't be replacing the pipe where the bov is. the pipe from the turbo to the stock intercooler will still be used, as will the pipe with the bov on it. the 3 bits of pipe shown go from where the stock intercooler sits to the fmic, and then the other 2 go from the fmic to the side fire wall and the next from the side firewall to the pipe with the bov on it.

as for the bov, just get an adapter. the best plave to have a bov fitted is as close to the throttle body as possible. it keeps the air flowing in the one direction.

unless there is more piping for your fmic kit that what is show, you won't be replacing the pipe where the bov is. the pipe from the turbo to the stock intercooler will still be used, as will the pipe with the bov on it. the 3 bits of pipe shown go from where the stock intercooler sits to the fmic, and then the other 2 go from the fmic to the side fire wall and the next from the side firewall to the pipe with the bov on it.

as for the bov, just get an adapter. the best plave to have a bov fitted is as close to the throttle body as possible. it keeps the air flowing in the one direction.

what he said, u wont need to replace the pipe that the BOV is connected to ;)

unless there is more piping for your fmic kit that what is show, you won't be replacing the pipe where the bov is. the pipe from the turbo to the stock intercooler will still be used, as will the pipe with the bov on it. the 3 bits of pipe shown go from where the stock intercooler sits to the fmic, and then the other 2 go from the fmic to the side fire wall and the next from the side firewall to the pipe with the bov on it.

as for the bov, just get an adapter. the best plave to have a bov fitted is as close to the throttle body as possible. it keeps the air flowing in the one direction.

The pipe in the top of the front mount kit shown is the pipe that replaces the one my bov is on, and joins to the pipe off the throttle body. Correct me if Im wrong but pretty sure thats right. All the kits, ive seen, cheap ones included join there, run across the fan shroud area and down the side that currently has no pipes (right hand side of car). Which then joins onto one on the right hand side of cooler and the left hand side pipe joins to standard pipe which then runs to turbo??? Can anyone confirm this.?

The pipe in the top of the front mount kit shown is the pipe that replaces the one my bov is on, and joins to the pipe off the throttle body. Correct me if Im wrong but pretty sure thats right. All the kits, ive seen, cheap ones included join there, run across the fan shroud area and down the side that currently has no pipes (right hand side of car). Which then joins onto one on the right hand side of cooler and the left hand side pipe joins to standard pipe which then runs to turbo??? Can anyone confirm this.?

no you dont replace that bit.

The pipe in the top of the front mount kit shown is the pipe that replaces the one my bov is on, and joins to the pipe off the throttle body. Correct me if Im wrong but pretty sure thats right. All the kits, ive seen, cheap ones included join there, run across the fan shroud area and down the side that currently has no pipes (right hand side of car). Which then joins onto one on the right hand side of cooler and the left hand side pipe joins to standard pipe which then runs to turbo??? Can anyone confirm this.?

i'm assuming that you are talking about the pipe with the bracket on it? that bracket bolts to the drivers side of the motor near the injector rail. it runs from under the radiator hose on the drivers side to the start of the pipe with the bov on it. the pipe on the left of the cooler in the pic you posted runds from the drivers side of the cooler, through the holoe you have to cut in the side firewall, to the start of the pipe i just mentioned. the pipe on the right of the cooler runs from the where the stock cooler sits (so it joins the stock pipe that comes from the turbo) to the passenger side of the fmic.

The pipe in the top of the front mount kit shown is the pipe that replaces the one my bov is on, and joins to the pipe off the throttle body.

i think he is a bit confused as to what goes where.

either way, just get an adapter and mount the blitz bov on the stock bov's location.

i think he is a bit confused as to what goes where.

either way, just get an adapter and mount the blitz bov on the stock bov's location.

I think you are confused.. he is talking about the COLD pipe coming from the stock cooler, it has his Blitz BOV attached to it. THIS pipe will be replaced by the piping in the kit, he is asking if he should try put his Blitz BOV in the same spot that it currently is or put it on the crossover pipe where the stock BOV sits.

I've seen adaptors for RB20/25's are my local Malz (our version of Autobarn), bolts in the stock location and has a 90deg bend in it. My R2D2 was actually mounted inside the front right guard.. well out of the way of prying police eyes :action-smiley-069:

Edited by bubba

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
    • Pull codes via the self-diagnosis procedure. As far as I can tell this is just a sign of transmission issues but not a code unto itself.
    • Hi All, putting the engine back together and everything is perfect except have this plug left over.. any ideas what it is for and where it goes? Is on cold side under the intake plenum *note not a stock plug, as everything has been modified Cheers
×
×
  • Create New...