Jump to content
SAU Community

Recommended Posts

And got a cannon!!

lol.. My muffler at the moment sounds like a POS.. It sounds way too raspy.. Plus this was 20% off and with a 2.25 inlet ( which I could not find anywhere), it matched my system atm perfectly har har.

4utu0xw.jpg

Hopefully it doesn't end up sounding like a POS though, I'm a little worried about the length of the tip, seems shorter to most cars I've seen lately.. Not sure how that will impact?.. And hopefully not too much if any back pressure is lost, s It's still 2.25 so fingers are crossed.. Will post a vid when it goes on some time next week.

EDIT: Vids are up now.. 1st, begins with early stages of the car, and the last vid is of th car now..

First video is when the car had only the exhaust.

Second Video is after extractors + Pod with the same exhaust.

Third video is with the new cannon lol

Link to comment
https://www.sau.com.au/forums/topic/173908-so-i-went-over-to-the-darkside/
Share on other sites

ure car didnt sound to bad on the last cruise we went on, i wana see a vid of this hope it sounds gud. i changed my catback yet again

It sounded too raspy mang. Atleast from my perspective.. I've never been behind it so I suppose I don't really know for sure lol.. But still I want to see what it sounds like with this eh..

Revving in neutral doesn't really show much, really gotta do a drive by as its always going to sound different under load. Personally I've never really heard any NA rb's that sound nice, most have a horrible rasp to them.

I shall get on the drive by asap

Generally the N/A's only get a nasty rasp when they rus stainless rear mufflers without suitable mufflers further up the sytem. Mine runs all mild steel and standard bore diameter and sounds like this.

http://homepages.paradise.net.nz/jswright/Scream.mp3

Ignuz, yours doesn't sound too bad at all for running a cannon. Good work.

I resisted the urge to go cannon and went for a twin outlet (squared tips) Zetti exhaust when I did the upgrade about 18 months ago. I also went the Coby Extractor route, and upgraded to stainless hi-flow cat while I was at it. I even sent the extractors & exhaust to Brissy to be HPC coated just for good measure... Now it all sounds VERY loud, particularly inside for passengers. I'm putting the noise factor down to the extractors more than the exhaust, but either way it's damn loud!

From what I've heard and experienced, the raspy noise never seems to leave N/As... you can only make the exhaust louder to drown out the annoying rasp when accelerating. Believe me I've tried everything I can think of to get rid of it with my car.

i put a 4inch shitbox autobarn cannon on my old NA auto r33, jesus christ it was loud

resonating so hard inside the cabin and shaking the earwax from my ears while doing 40kph up a hill.so many headaches, i got out of the car 3/4 def

never again will i make that mistake. as for power gains well seeing it was on an NA it raped my low torque and didnt notice a difference apart from drinking more fuel.

  • 1 month later...
i put a 4inch shitbox autobarn cannon on my old NA auto r33, jesus christ it was loud

resonating so hard inside the cabin and shaking the earwax from my ears while doing 40kph up a hill.so many headaches, i got out of the car 3/4 def

never again will i make that mistake. as for power gains well seeing it was on an NA it raped my low torque and didnt notice a difference apart from drinking more fuel.

Lol mine doesn't seem to drone, it more or less is just pretty loud when you go over 3k RPM.

Only vid of a drive by I have at the moment..

1. No I don't have a fake BoV

2. No I don't know what that psssssttt sound is in the vid from the car

3. Just saying this because a few people have asked already.

http://www.youtube.com/watch?v=nh-14jWBaUo

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hopefully it ends up being something manageable, like a hone, rather than a full bore—it would be a huge relief if it’s not as bad as it looks. Hang in there; these setbacks are annoying, but it sounds like you’re handling it as smartly as possible.
    • At the end of the day, it’s all about understanding the odds and being comfortable with the potential cost, whether it’s horsepower on a build or chips on a roulette table. And I have to say, the Laine example made me laugh—some people really do embrace that carefree, “roll and see” attitude!
    • Thanks MBS206, i got that PDF but got abit overhelm with all the connections and tracing of wires. I wasn't expecting to plug the dash harness anywhere. i was just going to use my electronics jumper wires to plug into the right pins like ECU power, ecu ground, ignition trigger etc... I do have a few ratchet straps locking it down tight. Fire extinguisher ready and only a small amount of fuel at a time, enough to submerge the pump.
    • Thanks GTSBoy, i will do abit more digging. I am missing a blue relay near the ECU connector... so i will chase that up in the next few days as well  
    • https://yariksteel.ru/manual/R33/Skyline_R33_elektroprovodka.pdf   Page 18 should be what you want for the Dash Cluster wiring. Though, you don't need the dash plugged in to get the motor running. What you want is power as how GTSBoy said. You need to power the ECU. Find in the above link the ECU pin outs (Verify them before just connecting them up from things written on the internet). Find anything needing power, give it power, find anything needing ground, give it ground. Then give the starter motor power through a big cable, and bridge the solenoid on the starter straight to power too.  ECU will be on, and when you give the starter power, it'll spin the starter motor, and it should start. I also hope you have a proper stand, and not just the engine sitting on some wood. You will want it bolted down properly.
×
×
  • Create New...