Jump to content
SAU Community

Recommended Posts

i c... dunno about you, but I myself wish I have an AWD car, much improved wet handling compared to RWD....

u gotta take out both the fuse and the front shaft, otherwise you might break something, like burn the transfer case.

I have installed a switch that runs inline with the 4WD fuse. I use it all the time and have seen no problem for the last year of using it.

Of course, the ignition has to be off before the use of the switch will take effect. (ie: no alternating between 4WD and RWD on 'the fly')

If you don't wish to install a switch, simply remove the 4WD fuse from in the engine bay. And no, ABS is not affected by this.

Guest Dragon

There is another 'trick' if you wish to 'try' running it in 2WD mode 'without' pulling the fuse.

Drive along the road, say about 40km/h (Make sure the turbo is cool for this) push the clutch in, coast along, switch the engine off (Must be in a straight line, clear of ALL traffic. Hit the kill switch on your turbo timer if you have one.)

Once the engine has died, switch back on and start. (Do this while still coasting along)

Let out clutch and you will be in RWD mode.

PRO's: Instant change on the fly to RWD. No need to pull fuse. Can test to see what it is like quickly in RWD mode.

CON's: Disables ABS/HIACS. ABS/HIACS lights will come on. AWD system will engage again once you stop moving forward!

How this works in this............

When you start the car (R32 GTS-4/GTR) the ATTESSA (Spelling?) system tests itself. Normally when you first start a car, it is NOT moving, soo all sensors report back that all is fine and dandy.

But, if you start the car WHILE it is rolling along, then the sensors report there is a problem! Shuts down AWD and goes into RWD mode.

If you have ABS/HIACS fitted, these also will shut down.

I have tried this on a R32 GTR and it works a treat! It 'should' work on a R32 GTS-4.

Have fun!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • When you crank your car, and hit it with a timing light, can you see a steady crank timing?
    • Oh, forgot to add, A few months ago I was getting mixture codes and the car was using crap loads of fuel. You could smell the unburned fuel in the exhaust, it was crazy strong. Economy was over 17.5 l/100 and usually around 19. I smoked the engine and found a leaky CCV hose which I replaced and then I replaced my two pre cat O2 sensors, I also replaced the MAF. This fixed my mixture codes and improved my exonomy but I'm still 14 - 15 l/100 when pottering about town so something is still amiss. Throttle response is much better and it has more pep but I'd like to know why it's still so thirsty (and I'm hoping that whatever it is gives me a bit more poke).    
    • Car is on factory injectors/z32 maf/ q45 throttle body/ z32 ecu with nistune 
    • Hello all, currently finishing up a rb25 swap into my s14. Having issues with starting, car has spark (confirmed by pulling a plug and watching it spark), has fuel(confirmed by checking pulse/voltage at injectors all spark plugs are soaked in fuel). Car cranks over and pops into the exhaust with a heavy fuel smell but no attempt to start or run, I have torn the timing cover off and triple confirmed timing, turned the CAS in multiple spots both directions, attempted to start with coolant temp and maf unplugged, checked my fuel lines and made sure they weren’t backwards, checked voltage at cas/injectors/coilpacks, made sure all the grounds in the harness are connected and added a few grounding straps (1 from chassis to block, 1 from chassis to head, and 1 from chassis to igniter chip) I am getting stumped here. As a last ditch effort I made a full grounding harness tonight that’s going to run from the battery and add an extra ground from the battery onto the coil pack harness/igniter chip/ intake manifold/ Wiring specialties harness ground/ and alternator. I’m hoping maybe the grounding harness will fix it here but posting here to see if anyone has any other ideas on what else I can check. My fuel pressure is unknown right gauge will be here tomorrow.  IMG_3206.mov
    • yeah I was shocked when I checked my spare OEM on and as below that's how they come from Nissan. (side interesting note new NEO gearbox and replacement park lack the brass bush on the tips and its just all alloy) unsure about damage to the box currently back at 1110 to be pulled down/inspected and selector fork replaced as he built it previously and given the never before seen failure on his billet forks he is replacing it under warranty. He said he has used always OEM the keyway tab without issue for years so it could be an unlucky coincidence. I did talk to him about the sharp corners and stress concentration too. Re: hard shifts i got 7+ years out of the OEM one and the fork itself failed not the keyway. so could be bad luck as I said or an age thing + heat cycles in box and during fabrication of billet?
×
×
  • Create New...