Jump to content
SAU Community

Re 001

SKYGTT

By SKYGTT,
in South Australia

 Share

Recommended Posts

pkblade Experienced

pkblade

Posted
Posted
what so good about them???

As mentioned it's replacing the S03 & supposedly was tested at Mallalla against the S03 & had better lap times.

Bridgestone seem to be very confident with it's performance as they've spent $$$$ on marketing.

I was quite impressed with the Adrenalins & will definitely be getting a set once I go through my T1-Rs.

Link to comment
https://www.sau.com.au/forums/topic/174165-re-001/#findComment-3197140
Share on other sites
Tangles Grand Master

Tangles

Posted
Posted

I had G3's on my old VR V8 cop car.

ok tyres, but really, for the cash, they were crap.... crap i say. wife lost it a cple of times. just didnt have the grip youd expect them to have, on a slippery surface.

best priced and performing tyres Ive ever used on a car are my current fare; Hankook Ventus K104 awesome tyre, $190 ea for 17x 235

I dont see how you can lose traction with these tyres on the street - if you do then you're doing something wrong. ie coming too hot into a corner, or perhaps braking thru the corner (big no-no; always end your braking B4 you hook into the crnr)

mind you, i do have AWD and a few extra hundred kgs in the stagea so maybe that makes a difference to a RWD skyline, in the way that they handle..... but this set should last 4yrs (35,000kms). top value. id argue that with anyone.

best bike tyres Ive had were Michelin Pilot's, top of the range goodness :) $290 for rear and $230 for front. worst tyre was Michelin sports, long range tyre not made for kneedown cornering. meant to last 12000kms, I ripped mine up in 5000 lol.

Link to comment
https://www.sau.com.au/forums/topic/174165-re-001/#findComment-3197994
Share on other sites
Pauly33GTS-t Veteran

Pauly33GTS-t

Posted
Posted

michelins hot spot is in the high temperatures tho isnt it, whereas bridgestone is better known as an all rounder and wet control tyre.

Id take pirellis over both tho. but I am going to go with these andrenalines ive decided.

Link to comment
https://www.sau.com.au/forums/topic/174165-re-001/#findComment-3198119
Share on other sites
Nightcrawler Grand Master

Nightcrawler

Posted
Posted

I had GIIIs on the R34 and they were absolutely brilliant. Only problem was when I went to replace them the rear 255s were going to cost $450 each!

Went for Michelin Pilots and they have been awesome, but as usual I only got just over 10,000km from them.

Might try these out next.

Link to comment
https://www.sau.com.au/forums/topic/174165-re-001/#findComment-3198187
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Latest Posts

    • GTSBoy
      DeAgostini 1/8 scale BNR32 Nissan Skyline GT-R Nismo

      By GTSBoy · Posted

      That's hilariously putrid!
    • GTSBoy
      R33 Fuel Pump & Brakes after alarm swap

      By GTSBoy · Posted

      When I said "wiring diagram", I meant the car's wiring diagram. You need to understand how and when 12V appears on certain wires/terminals, when 0V is allowed to appear on certain wires/terminals (which is the difference between supply side switching, and earth side switching), for the way that the car is supposed to work without the immobiliser. Then you start looking for those voltages in the appropriate places at the appropriate times (ie, relay terminals, ECU terminals, fuel pump terminals, at different ignition switch positions, and at times such as "immediately after switching to ON" and "say, 5-10s after switching to ON". You will find that you are not getting what you need when and where you need it, and because you understand what you need and when, from working through the wiring diagram, you can then likely work out why you're not getting it. And that will lead you to the mess that has been made of the associated wires around the immobiliser. But seriously, there is no way that we will be able to find or lead you to the fault from here. You will have to do it at the car, because it will be something f**ked up, and there are a near infinite number of ways for it to be f**ked up. The wiring diagram will give you wire colours and pin numbers and so you can do continuity testing and voltage/time probing and start to work out what is right and what is wrong. I can only close my eyes and imagine a rat's nest of wiring under the dash. You can actually see and touch it.
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      So I found this: https://www.efihardware.com/temperature-sensor-voltage-calculator I didn't know what the pullup resistor is. So I thought if I used my table of known values I could estimate it by putting a value into the pullup resistor, and this should line up with the voltages I had measured. Eventually I got this table out of it by using 210ohms as the pullup resistor. 180C 0.232V - Predicted 175C 0.254V - Predicted 170C 0.278V - Predicted 165C 0.305V - Predicted 160C 0.336V - Predicted 155C 0.369V - Predicted 150C 0.407V - Predicted 145C 0.448V - Predicted 140C 0.494V - Predicted 135C 0.545V - Predicted 130C 0.603V - Predicted 125C 0.668V - Predicted 120C 0.740V - Predicted 115C 0.817V - Predicted 110C 0.914V - Predicted 105C 1.023V - Predicted 100C 1.15V 90C 1.42V - Predicted 85C 1.59V 80C 1.74V 75C 1.94V 70C 2.10V 65C 2.33V 60C 2.56V 58C 2.68V 57C 2.70V 56C 2.74V 55C 2.78V 54C 2.80V 50C 2.98V 49C 3.06V 47C 3.18V 45C 3.23V 43C 3.36V 40C 3.51V 37C 3.67V 35C 3.75V 30C 4.00V As before, the formula in HPTuners is here: https://www.hptuners.com/documentation/files/VCM-Scanner/Content/vcm_scanner/defining_a_transform.htm?Highlight=defining a transform Specifically: In my case I used 50C and 150C, given the sensor is supposedly for that. Input 1 = 2.98V Output 1 = 50C Input 2 = 0.407V Output 2 = 150C (0.407-2.98) / (150-50) -2.573/100 = -0.02573 2.98/-0.02573 + 47.045 = 50 So the corresponding formula should be: (Input / -0.02573) + 47.045 = Output.   If someone can confirm my math it'd be great. Supposedly you can pick any two pairs of the data to make this formula.
    • Jarsky
      R33 Fuel Pump & Brakes after alarm swap

      By Jarsky · Posted

      Well this shows me the fuel pump relay is inside the base of the drivers A Pillar, and goes into the main power wire, and it connects to the ignition. The alarm is.... in the base of the drivers A Pillar. The issue is that I'm not getting 12v to the pump at ignition which tells me that relay isn't being triggered. AVS told me the immobiliser should be open until the ignition is active. So once ignition is active, the immobiliser relay should be telling that fuel pump relay to close which completes the circuit. But I'm not getting voltage at the relay in the rear triggered by the ECU, which leaves me back at the same assumption that that relay was never connected into the immobiliser. This is what I'm trying to verify, that my assumption is the most likely scenario and I'll go back to the alarm tech yet again that he needs to fix his work.      Here is the alarms wiring diagram, so my assumption is IM3A, IM3B, or both, aren't connected or improper. But this is all sealed up, with black wiring, and loomed  
    • hardsteppa
      Hi everyone.

      By hardsteppa · Posted

      Ceste, jak se mas Marek...sorry I only have english keyboard. Are you a fan of Poland's greatest band ever?   
×
×
  • Create New...