Jump to content
SAU Community

Recommended Posts

If you want more distance, get some that can use the various repeaters around. They can extend the distance a fair way - we used to get from Dandy area to Melton on a good day (roughly 50-60kms).

I've been looking at some Icom units, but they are fairly expensive... About the size of my current Nokia, so nice & easy to carry. They can also work at full power (5W) so a good 25km can be reached without a repeater.

About $360-$400 last time I looked.

  • Replies 70
  • Created
  • Last Reply

Top Posters In This Topic

yeah... those GME ones can use repeaters. The Uniden UH052XR is a good one too. RRP $419.00

As per the GME site

Duplex

Provides greatly increased range by allowing access to any of the hundreds of UHF CB repeaters installed around the country

Originally posted by acsplit

SKY031 you bag everything

Yeah, I'm gonna bag you in a minute, with lots of plastic and tape.

:D

I didn't bag anything. :cheers:

I was just saying, that as far as UHF radios go, theres no point in spending heaps if you're only using it for cruising.

GiJOr33 there aren't many active repeaters around Melbourne.

There is one in Berwick (channel 3), and one located somewhere around the city (channel 2) but due to the decline in the use of UHF radios, and the increasing cost of running a repeater, the repeaters have just gradually shut down and haven't re-opened.

(This includes channel 5 emergency which is no longer available)

Don't buy a radio just because it's advertising duplex as a feature, most of the cheaper (under $100) ones have duplex function as well.:D

if someone can get them trade then thats great as the bst discount i can do is $120 as i get them through my work (trade discount) but would need to purschase 10 or more

and yes you can get the incar base units which are a lot more in price

check out the web site

www.gme.net.au

any more queries email me

[email protected]

but acssplit is getting them.... So where do ya work Andrew

are you talking to me? cos my name is Andrew as well... and if you are talking to me... how do you know my name?!

I run my own business.... so just apply to the dealers when i need to.

GiJOr33 said:

are you talking to me? cos my name is Andrew as well... and if you are talking to me... how do you know my name?!

GiJOr33 & acsplit are both named Andrew

ash3 and R31 Nismoid are both named Ash

Maybe we should just call everyone by forum names to avoid confusion. :confused:

Originally posted by RedLineGTR

i still would like someone who has used them to recommend one or maybe some ovious differences between them

redline i have used both and use them both frequently so pm me and i will tell you the advantages pros cons etc

i have to go to the movies now so i will reply later

but for the extra $25 gme is well worth it and i don't use the 38 ctcs encoding feature either

that would make the Uniden one the pick of the bunch with 2w of power... extra distance rather than private encoding

what if there are lots of people and you want your own channel? cos a cruise will mean plenty of people with cb's and if you want a channel with you closer mates, you can enable the ctcss and have one.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • So could it be assumed it has been installed intentionally with potentially a power FC boost controller kit? 
    • Had my rig on Matt's dyno at PITS the other day. After a few years between tunes I added a few sensors and swapped intercoolers. Result. 553hp at 26psi. Not bad for an FJ20 that was built in 2007. The problem.. It filled the overflow bottle on hard runs which leads me to believe the head gasket isn't sealing. I have a coolant pressure sensor which was reading cap pressure at 22psi and occasionally overrunning to 23/24 psi on deceleration after a pull. It was not spiking. It has arp2000 head studs and a cometic gasket. As its been 18 years in service, I pulled the engine out and head off. Everything looks good but we obviously have an issue. Where I'm at.. Years ago I had the same issue, I checked the stud tension and they were all over the place. Some at 60 to 70 and some up near 90. I nipped them all to 100ft lbs and this stopped the water push until now. I believe this compromised the gasket back then. What do I do? 2 options are..  1) I bought arp 625+s, which I could put in with a new gasket. Thinking Kameari this time, reassemble and try again. 2) strip the block, get fire rings machined in with copper gasket and try that. I do not want to push it more than 28 to 30psi. I think the turbo will be out by then anyway. (G30-770). My other concern is the long term ability of a copper head gasket. Are they streetable for years? I feel like a new gasket with the new studs will probably suffice, but I don't know. Any thoughts welcome and advice on copper gaskets and fire rings. Thanks!
    • I'm a fan of the JZX110, and the Aristo. Big cruiser cars, and with the factory cars, super comfortable and feel like you're driving an armchair! And the JZ motors are a pretty nice engine too, especially with some basic mods.   The import process, and the need to be able to trust people, and the fact there's so many scammers around is what ever puts me off wanting to go through that ordeal!
    • I don't care for these at all, but at least the underside looks straight and not rusty. A good basis for a long life. Many cars from Japan have been lifted with forklifts and f**ked almost irrepairably.
    • Yes, but it's not dumb or dodgy. You can build a perfectly good boost controller from a pressure reg, a relief valve (looks same same as a reg if all from Norgren or SMC, for example) and a check valve. I ran one for years. Only superceded with  EBC because I could get one for cheaps and wanted finer control.   THis mod is certainly not a sketchy boost mod, provided the boost is kept below the "spin to death" threshold of the turbos.
×
×
  • Create New...