Jump to content
SAU Community

Recommended Posts

Hey guys,

I'm selling my TEIN coilovers, they are in very good condition only used for short time in my R33 as car got sold.

and now have no further use for them.

They are in fantastic condition and suit both R33 and R34 4door.

Would like $900 but negotiable as always.

Also have ZCAS japanese performance breakpads. 4 Pads They are brand new in box, suited for R32. $150

Located in adelaide. Local pickup is welcome and am also willing to send interstate.

Cheers

post-20233-1184485304_thumb.jpg

post-20233-1184485346_thumb.jpg

post-20233-1184485426_thumb.jpg

post-20233-1184485467_thumb.jpg

hey mate i am keen on the coil overs, how old are they and can i get the model numbers of the side, fark you had them set low......

hey mate i am keen on the coil overs, how old are they and can i get the model numbers of the side, fark you had them set low......

hey mate, i only had them in my car for a couple of months.

i'll pm you the model numbers after work tonight.

where are you located?

just out of curiousity how much are you charging for postage to brisbane qld 4301 for the coilovers

i've sent a pair to qld before a while ago and i think i paid $80 registered post

i'll double check though

u say these will go on 4doors but wat about r34 coupes

not quite

the front is exactly the same on the r33 and r34 coupe and sedan

however the rear set is a bit different, the mounts are the same, but the bottom of it is different between the coupes and sedans.

whats the rear look like on yours?

spring rates???

pm me ur best price to brisbane..

not too sure of spring rates, was quite a comfortable ride though.

coupes and sedans have the same suspension setup for GTT. Unless you are comparing NA and turbo then there is a difference. So if yours came off a GTT sedan, it will definately fit a GTT coupe.

coupes and sedans have the same suspension setup for GTT. Unless you are comparing NA and turbo then there is a difference. So if yours came off a GTT sedan, it will definately fit a GTT coupe.

i'll post up pics of the difference between coupes and sedans, just so that someone doesnt end up buying it and it doesnt end up fitting.

hope this will take care of the confusion, the standard struts are from an R34 COUPE

the bottom of the strut is different shaped to that of the coilovers, the mounts on the top are exactly the same.

I'm not sure if every R34 coupe is the same though.

post-20233-1184978303_thumb.jpg

post-20233-1184978334_thumb.jpg

post-20233-1184978365_thumb.jpg

Sorry don't mean to spam ur thread, jst want to set the record straight, as I mentioned before, GTT coupe and sedan suspension is exactly the same (front strut has an eye and rears have the fork)

What you have should fit an NA R34 sedan or coupe or a GTV as they are called. They have an eye on the rear strut instead of a fork. I have attached pics of my Teins to suit GTT sedan or coupe. Hope this clears things up and GL with ur sale.

post-6973-1184979998_thumb.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yup. You can get creative and make a sort of "bracket" with cable ties. Put 2 around the sender with a third passing underneath them strapped down against the sender. Then that third one is able to be passed through some hole at right angles to the orientation of the sender. Or some variation on the theme. Yes.... ummm, with caveats? I mean, the sender is BSP and you would likely have AN stuff on the hose, so yes, there would be the adapter you mention. But the block end will either be 1/8 NPT if that thread is still OK in there, or you can drill and tap it out to 1/4 BSP or NPT and use appropriate adapter there. As it stands, your mention of 1/8 BSPT male seems... wrong for the 1/8 NPT female it has to go into. The hose will be better, because even with the bush, the mass of the sender will be "hanging" off a hard threaded connection and will add some stress/strain to that. It might fail in the future. The hose eliminates almost all such risk - but adds in several more threaded connections to leak from! It really should be tapered, but it looks very long in that photo with no taper visible. If you have it in hand you should be able to see if it tapered or not. There technically is no possibility of a mechanical seal with a parallel male in a parallel female, so it is hard to believe that it is parallel male, but weirder things have happened. Maybe it's meant to seat on some surface when screwed in on the original installation? Anyway, at that thread size, parallel in parallel, with tape and goop, will seal just fine.
    • How do you propose I cable tie this: To something securely? Is it really just a case of finding a couple of holes and ziptying it there so it never goes flying or starts dangling around, more or less? Then run a 1/8 BSP Female to [hose adapter of choice?/AN?] and then the opposing fitting at the bush-into-oil-block end? being the hose-into-realistically likely a 1/8 BSPT male) Is this going to provide any real benefit over using a stainless/steel 1/4 to 1/8 BSPT reducing bush? I am making the assumption the OEM sender is BSPT not BSPP/BSP
    • I fashioned a ramp out of a couple of pieces of 140x35 lumber, to get the bumper up slightly, and then one of these is what I use
    • I wouldn't worry about dissimilar metal corrosion, should you just buy/make a steel replacement. There will be thread tape and sealant compound between the metals. The few little spots where they touch each other will be deep inside the joint, unable to get wet. And the alloy block is much much larger than a small steel fitting, so there is plenty of "sacrificial" capacity there. Any bush you put in there will be dissimilar anyway. Either steel or brass. Maybe stainless. All of them are different to the other parts in the chain. But what I said above still applies.
    • You are all good then, I didn't realise the port was in a part you can (have!) remove. Just pull the broken part out, clean it and the threads should be fine. Yes, the whole point about remote mounting is it takes almost all of the vibration out via the flexible hose. You just need a convenient chassis point and a cable tie or 3.
×
×
  • Create New...