Jump to content
SAU Community

Recommended Posts

as the topic states today i bought a fujitsubo 2.5" cat-bak exhaust 2nd hand for $150 bought it locally from rolin imports in burleigh on the gold coast. i have some pics up and will install it this weekend.The exhaust is stamped fujitsubo and jasma. just wanted to know how much this exhaust would cost brand new? also some stories about the performance of the exhaust if youve installed it on your na skylines? as well as the sound of it (sound files if available).

p.s any tips on undoing the exhaust bolts?

thanks guys pics are attached (this will be installed on my r32 gts25)

post-36737-1184750107_thumb.jpg

post-36737-1184750141_thumb.jpg

post-36737-1184750205_thumb.jpg

post-36737-1184750239_thumb.jpg

post-36737-1184750264_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/177106-bought-25-fujitsubo-exhaust-for-150/
Share on other sites

hey mate. fujitsubo are a good exhaust. i got a video here

of mine with a 2.5inch fujitsubo cat back. there not cheap i know that so for 150 bucks you got a bargain. if you need to get the exhaust bolts off torque wrench or breaker bar something long that you can apply more force with. just make sure you dont strip the bolts

just measured the width of the pipe and it actually is 3" not 2.5" i was misinformed by rolin automotive. how will this affect the engine? ive heard it will drone a lot but i always have the music up so it doesnt matter.i will still put it on just need these q's answered first.

my standard cat has a 2" outlet hole with flange, the exhaust has a 3" inlet hole with flange, the bolt holes for the cat flange and the exhaust flange are the same (11cm apart from middle of bolt hole to middle of bolt hole) so im guessing this will fit right??

can i buy new exhaust flanges from supercheap?

p.s later on i will throw a turbo on my car so it saves me having 2 buy a 3" when i do.YAY!

thanks again

sorry for the long post

Edited by adoboy666

well i take that back the jealousy then.

how will it affect the engine?

- it will be a pig to drive

- absolutely gutless at low rpm

- the sound will be like you said droney

- you will use more fuel

- more power at a higher rpm

flange sizes should fit, if not just re-weld a new set on at your local exhaust shop.

don't think supercheap carry flanges.

p.s later on i will throw a turbo on my car so it saves me having 2 buy a 3" when i do.YAY!

that is the silliest thing i've ever heard... it's not like you're doing any favors to your wallet by getting your exhaust out of the way.

the increase in fuel, emissions and power loss may annoy you long before you begin your conversion. but each to their own.

just keep in mind that the amount of kw you have is not an indication of how quick/well performing your car is.

<br />well i take that back the jealousy then.<br /><br />how will it affect the engine?<br />- it will be a pig to drive<br />- absolutely gutless at low rpm<br />- the sound will be like you said droney<br />- you will use more fuel<br />- more power at a higher rpm<br /><br />flange sizes should fit, if not just re-weld a new set on at your local exhaust shop.<br />don't think supercheap carry flanges.<br /><br /><br />that is the silliest thing i've ever heard... it's not like you're doing any favors to your wallet by getting your exhaust out of the way.<br />the increase in fuel, emissions and power loss may annoy you long before you begin your conversion. but each to their own.<br />just keep in mind that the amount of kw you have is not an indication of how quick/well performing your car is.<br />
<br /><br /><br />

Do you think if i get a silencer made up it will help could give me back some precious backpressure??

anyone have any estimate on the cost for getting one made??

thanks again

<br /><br /><br />

Do you think if i get a silencer made up it will help could give me back some precious backpressure??

anyone have any estimate on the cost for getting one made??

thanks again

You loose backpreassure due to not having enough volumetric vacume (WOOO! I USED IT EUGENE! :D )

I silencer will do nothing besides add weight and make your car slightly quieter..

Only way you can get ur back preasure back.. is.. go to a smaller zorst..

You loose backpreassure due to not having enough volumetric vacume (WOOO! I USED IT EUGENE! :laugh: )

I silencer will do nothing besides add weight and make your car slightly quieter..

Only way you can get ur back preasure back.. is.. go to a smaller zorst..

The exhaust sounds sweet, it is drony and i have lost my bottom end but my top end torque feels great, will post up an audio file of it soon, wat should i use to record it?

You loose backpreassure due to not having enough volumetric vacume (WOOO! I USED IT EUGENE! :P )

I silencer will do nothing besides add weight and make your car slightly quieter..

Only way you can get ur back preasure back.. is.. go to a smaller zorst..

hmm is the opposite true? meaning that if I have a 2.5inch and i put a silencer in, it won't cause it to be restrictive again?

cheers

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • looking for some help and maybe some insight on others experience with a new LSD. R34 GT ran and drive beautifully, but always alot of grip loss due to the open R200 rear end, so I just installed a new 1.5 LSD way into the stock open R200 for a ER34. Simple. Everything seemed right. I test drove for the first time this weekend. as I started to back out the garage the first time slowly with tires straight it sounded and felt like I had a loose or half disconnected drive shaft...that was clucking around loose and shaking entire vehicle, and making it feel like the trans clutch was spontaneously slipping then grabbing very roughly while just letting out pedal slowly. I backed it out went to pull forward with the same noise, shake and slip grab feeling with hesitation, I turned the tires to back out more and then pulled ahead some same thing but worst because of added wheel resistance (which that I expected) puzzled … pulling it back in checking everything over and finding nothing wrong, I tried it the next day. same thing, couldn’t believe how it shook everything again making a terrible noise and making it feel like the trans clutch was slipping and grabbing, but I got it out of garage into the driveway, got it straight, drove forward and then reveres a few times in a straight line everything shaking , causing what felt like clutch slip and grab every time, sounded like right behind front driver tire and I could feel it in the floor board with my feet,... worst right when beginning to let clutch pedal out to engage slightly, shuttering and sounding terrible along the way…I managed to slowly get down the road, babying it the whole way, once I was rolling (out of 1st) seemed to be better and between shifts, then clutch felt closer to normal…not slip/ grab etc., but back down to any stop, straight road or turning, same thing. Made no difference if all tires were straight or if I was turning. All other gauge read out correct. with in 2 miles as planned I reached the empty parking lot and performed the break in procedure that came with lsd, essentially to drive in a figure 8 a bunch.  Did this, binding chattering, and shaking the car the whole way. I drove it back home seemed somewhat normal once I was in straight line and past 10 mph or so, and I know it will “bind” on corners and cause some tires squeal when turning especially from a stop, but when I begin to move it still causes what feels like the trans clutch to slip and jerk badly as well as shaking the entire car, and sounds terrible, that I didn’t expect. I used the fluid they supplied with LSD kit and did the breaking, planning to change fluid as they suggest after breaking, but wondering will it get smoother or less aggressive with use? maybe a 1.5 is just too aggressive for normal road driving?   I have a LSD that I put in my 71 cuda when I restored it, with amazing smooth , quite yet effective results. Different style LSD but that ones a joy to drive. maybe expecting too much from this R200?
    • Join SAU NSW for a flame-grilled feed & flame-spitting cruise! Sunday 17th August 2025 3:30PM Meeting Archies Flame Grille Sylvania Waters 4:45PM Cruise Departure 5:15PM Arrival at Cape Solander Kurnell Meet Location: Archies Flame Grille Final Destination: Cape Solander Kurnell *Disclaimer* There will be a lead and follow car so no one should get lost. If you would like to attend or bring others along please put your name down and a +1 as numbers will be needed prior! This is NOT a race and we will all be adhering to all road rules. If this is what you want please come to one of our many track days. This is an official SAU:NSW event and will be run under a CAMS permit. One of the things that really sets our club apart is our commitment to being true enthusiasts. When on normal roads we strive to maintain good relations with the authorities as well as the public in general. When attending one of Skylines Australia NSW events please try to: • Be aware of surrounding environment and act accordingly. • Drive courteously on the state’s roads as a true enthusiast should. • Understand how important it is to maintain the good name of SAU NSW and thus, treat others accordingly. • Any misbehavior will not be tolerated and you will be asked to leave.
    • Yeah good luck out there! Will be good to see a mighty GTST going harder than the GTRs
    • i will be there 😁
    • Hello!  i just finished manual swaping my r34 skyline with a r33 rb20de box(RB71C)box  When the car is running it squeaks crazy loud and it was smoking from the gearbox area. The gearbox is fine it was tested. The clutch slave cylinder seems like it doesn't fully releases the clutch. I want to ask if this noise is from the throw out bearing or could it be the clutch assembly or disk att.xFliq87Gzw6kImKBVqDebXkj0fBqymk0JaYeP3_3SlM.mp4
×
×
  • Create New...