Jump to content
SAU Community

Recommended Posts

Ok guys i have an R33 GTST S1.5

Current mods are

*K/N Pod filter

*Cat Back Blitz Nur Spec R Exhaust........think 3inch

*Apexi AVCR Boost controller

Ok so i think my coils are buggered because if i up the boost to about 11psi at around 4500rpm it runs like crap.....any suggestions?

So the plans are to get a

3inch Dump/Front pipe..........What should i do about the cat?

Split fire coils

High Flow turbo T3/T4 and run a max of 13psi

Apexi SAFC

With this combo should i hit the 200rwkw mark

Now on to my next question

Where in sydney should i take it to get a tune......need cheap and quality

Regards

Mick

Link to comment
https://www.sau.com.au/forums/topic/177283-sydney-dyno-and-mod-advice/
Share on other sites

i was making 204 rwkw with the following

- turbo back exhaust and high flow cat

- pod

-avcr (.95bar)

- fmic

-stock turbo

its a good tune that will make the car just as long as you have done the basic mods.

put in cam gears and pfc and made 224rwkw at .95bar

damn....sounds just like mine..

i have turbo back exhaust, fmic, pod, profec ii at .85 and stock ecu and made 202.6kw....

so you only put cam gear and pfc and made 224 of stock turbo at say 13psi?

Maybe i should invest in pfc....

hey simon that rb20 ecu is really interesting........how much does a full remap and tune cost for one.?

also if i just plugged in the 20 ecu would the car run as normal or needs to be remapped first>?

you should think about getting the eeprom copied im sure alot of people would be interested in buying that....

Mick

Edited by MrMike

Mick

The Map is not mine to sell, Mate of mine does the tuning for a reasonable price either way :banana: See my sig for details for The Speed Lab

As for the ECU, it is plug in and the car will probably start and idle but it wont be driveable thats for sure (rb20 has smaller injectors) so your best bet would be to leave the 33 ecu in there and drive to the tuner. Or get the 32 ecu epromed, buy chip from TSL and plug it in and drive it, Would be best to get it on a dyno to check everything before you really drive it hard tho.

As for price, ECU cost me 50 and the mapping/dyno time averages around 300-400 including chip install

I have a series 2 engine in the car will the rb20 ecu still work? sounds like a much better investment than the safc 2 i just bought. apparently the safc2 i bought has a 192rwkw tune on it.....how safe is it to run that tune on my car......

I have a diagnostic tool that i can monitor the knock signal and rich/lean mixtures while driving......if i have no detonation or continual rich/lean running .......it should be alright yes?

:D

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The rain is the best time to push to the edge of the grip limit. Water lubrication reduces the consumption of rubber without reducing the fun. I take pleasure in driving around the outside of numpties in Audis, WRXs, BRZs, etc, because they get all worried in the wet. They warm up faster than the engine oil does.
    • When they're dead cold, and in the wet, they're not very fun. RE003 are alright, they do harden very quickly and turn into literally $50 Pace tyres.
    • Yeah, I thought that Reedy's video was quite good because he compared old and new (as in, well used and quite new) AD09s, with what is generally considered to be the fast Yokohama in this category (ie, sporty road/track tyres) and a tyre that people might be able to use to extend the comparo out into the space of more expensive European tyres, being the Cup 2. No-one would ever agree that the Cup 2 is a poor tyre - many would suggest that it is close to the very top of the category. And, for them all to come out so close to each other, and for the cheaper tyre in the test to do so well against the others, in some cases being even faster, shows that (good, non-linglong) tyres are reaching a plateau in terms of how good they can get, and they're all sitting on that same plateau. Anyway, on the AD08R, AD09, RS4 that I've had on the car in recent years, I've never had a problem in the cold and wet. SA gets down to 0-10°C in winter. Not so often, but it was only 4°C when I got in the car this morning. Once the tyres are warm (ie, after about 2km), you can start to lay into them. I've never aquaplaned or suffered serious off-corner understeer or anything like that in the wet, that I would not have expected to happen with a more normal tyre. I had some RE003s, and they were shit in the dry, shit in the wet, shit everywhere. I would rate the RS4 and AD0x as being more trustworthy in the wet, once the rubber is warm. Bridgestone should be ashamed of the RE003.
    • This is why I gave the disclaimer about how I drive in the wet which I feel is pretty important. I have heard people think RS4's are horrible in the rain, but I have this feeling they must be driving (or attempting to drive) anywhere close to the grip limit. I legitimately drive at the speed limit/below speed the limit 100% of the time in the rain. More than happy to just commute along at 50kmh behind a train of cars in 5th gear etc. I do agree with you with regards to the temp and the 'quality' of the tyre Dose. Most UHP tyres aren't even up to temperature on the road anyway, even when going mad initial D canyon carving. It would be interesting to see a not-up-to-temp UHP tyre compared against a mere... normal...HP tyre at these temperatures. I don't think you're (or me in this case) is actually picking up grip with an RS4/AD09 on the road relative to something like a RE003 because the RS4/AD09 is not up to temp and the RE003 is closer to it's optimal operating window.
    • Either the bearing has been installed backwards OR the gearbox input shaft bearing is loosey goosey.   When in doubt, just put in a Samsonas in.
×
×
  • Create New...