Jump to content
SAU Community

Recommended Posts

Ok, so i installed them tonight

Gripes:

They have no thorough instructions

the ones that are in it, only showed how to remove the old coilpacks, and its not just a reverse installation...

Second

You cant just reinstall them into your old coilpack holders

it doesnt work...at all

you can install one bolt on each one, but when you put them on the car in the holder, its misaligned

so i didnt use it

BUt, when you install them without the holder, they are rather secure

they flop around but dont pull upwards, we shall see how it works out

It helped my idle immensly

its still high, but much more even

i also replaced plugs along with the coilpacks

TOmorrow ill bring it out for a test run before i install the wideband and SAFC2

see if it improved my boost problem at all...

anyways, more to come

Link to comment
https://www.sau.com.au/forums/topic/177931-splitfire-coilpacks/
Share on other sites

the one thing I did notice .. whilst reading the instuctions on how to change the coilpacks

I think the NEO uses a slightly different configuration than the non neo motors.

Looking at the how to article.. it seems that on the non NEO motors.. the coilpacks are grouped in 3 and attached to a plate ( 2 plates for 6 coilpacks ) on the NEO the coilpacks are just held in with 2 screws per coilpack. If you got the right coilpacks for the motor . and they are not a direct fit , I would be complaining or seeking re-embursment.

there is only one set for all years WGNC34

the non neo has the bracket that are grouped in 3

ill make some kind of bracket , not a big deal

just didnt know if it was only me that had that problem or not

maybe i have an odd holder?

i dunno

doesnt work for me...ghey

i cant speak for performance

but it improved my idle alot, its alot more smoothe

im installing my HKS acutator in like 10 minutes nad ill let you know how it performs once i get my boost back.

i think my wastegate is failing

man its going to be a bit of a headf*ck to make the bracket up accurately .

why not just send em back and say they dont fit? will be a lot easier.

from what I could see of the bracket that groups the 3 coil packs together it looks like its

made out of reasonably thick ally plate. Or why not just see if you can get that plate from

a wreakers etc?

well, theo problem is i bought them from a used place, but htey wre brand new

i got em for 350 USD

which is like 250 less than everywhere else

SO...its owrth the hastle, ill just trim off the mounting parts that cover hte larger holes, and get a piece of metal and make like a T with the bolt and metal to hold htem down.

shoudl only take an hour or so

well, theo problem is i bought them from a used place, but htey wre brand new

i got em for 350 USD

which is like 250 less than everywhere else

try buying your parts thru www.nengun.com (they are in Japan)

They are only $375 USD new for the right ones

I have been called worse haha..

no its just the 1st time doing it .. was just a bit of a pain .. compared to some of the other cars I have worked on . That and the breather hose being rock hard etc etc etc..

but .. got my good 1/4 drive ratchet set.. so those pesky alan keys holding the cover on dont stand a chance now.

plugs are hard to change?

Your crazy for saying that!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Welcome to my 2004 Toyota Mark ii IR-V Fortuna (series 2) With a 1JZ-GTE powerplant under the bonnet (hood) it'll give me plenty of scope for power upgrades. For those who aren't familiar with imports, the 1JZ-GTE is a 2.5L 6 cylinder VVTi engine with a single turbocharger. This has the factory R154 5 speed gearbox, along with a aftermarket 2 way LSD differential (brand unknown). Under the arches are a set of CST Zero 1 alloys, 18x9 +30 225/40 up front and 18x9.5 +15 265/35 on the rear. The car was quite low in Japan and there's evidence of the wheels catching the rolled arches/fenders. The tyre's aren't great so I'm in two minds whether to replace both or just the tyres and put up with the wider wheels on the rear. The car still uses stock brakes with the addition of some braided hoses. The exterior is stock with the exception of a BN Sports front bumper and a replacement Fortuna grill  Moving to the interior, the steering wheel has been replaced with a dished MOMO steering wheel (which will get swapped for my Momo Tuner for the time being) Defi Link Gauges are mounted above the climate controls and on the A pillar, the Oil Temp,Oil Pressure,Water Temp and Boost gauges should help with spirited and track driving  The stock seats have been replaced with some retrimmed Recaro bucket seats. Being a larger build these are a little snug, unfortunately the orange isn't for me so I'll look into replacing these down the line. Other modifications include a twin plate clutch, Blitz intercooler, Evolve alloy radiator, a stainless exhaust with decat, HKS EVC-S boost controller and coil overs
    • Apologies for the long read My R34 GTT was up for sale at the beginning of spring due to a few repairs creeping up. The strut tops needed replacing, roof and bonnet (hood) painting (yay for 3 stage pearl) and the underside stripped and treated. I sold the car which allowed me to be in a much better place financially. Leading up to the sale I was already thinking about the replacement. In an ideal world it needed to be a good all-rounder. Something I can mess around with, modify, do track days, do the school run, go on long drives etc.  Options included but not limited to... Laurel C35, Evo 8/9, Civic FD2, Impreza Hawkeye, Aristo and even an Audi S4 Avant (I've already got the Mazda 6 wagon). But there was always one car at the top of the list The Toyota Mark ii JZX110 I found an advert on a Facebook group for an example in Japan, from a seller called Jon at Rising Sun Exports. A few messages back and forth and Jon calls me from Yokohama one morning (or afternoon in his case). He briefly explained the import process, the costs involved and a repeat of the advert. After much deliberation, the price was agreed and the sale was locked in. I've never imported a vehicle so I jumped into the unknown head first. The money transfer was completed through wise.com (fees apply), very easy to use and the money was with him within a day or two.  The car suspension was raised for the vessel and the car dropped off at the port. It was 7 weeks later when the bill of lading was received and the freight invoice sent to me, followed by the export certificate a couple of days after (both digital copies) In the mean time the port had been in contact. I needed an agent to deal with the NOVA (notification of vehicle arrival) along with the tax/duty invoice, this was £75.00. The port also had a fee of £100, I'm guessing to cover the cost of the 10 day 'free storage' and for moving the car off the boat etc. They need a copy of the vehicle invoice, freight invoice and export certificate to allow the vehicle to pass through customs. The vessel arrived on Tuesday 5th August, the tax/duty invoice was generated and sent over. This is generally tax 20% and duty 10% of the vehicle value. Although the invoice came in at a higher amount than I had calculated. Once HMRC had received the payment the vehicle could be released from customs. I thought once the tax/duty was paid you could collect at any point, that's not the case. Your agent will need to book a collection slot, I requested Thursday 7th which was accepted, with a 9:00am slot allocated. It was a 5:00am start from Norfolk heading to Southampton. We eventually found the compound, upon presenting the bill of lading and some ID they released the car (they drove it out of the compound to the front ready for us to load up). The email from the port stated each slot had a 10 minute window, which seemed abit farfetched but the staff said it's not a strict rule. We were there for approx. 30-40 mins in total. A week prior to collecting I contacted my garage and explained the situation, I was able to get an inspection slot that afternoon. For the registration, DVLA require the car to be insured, for this I used a company called Adrian Flux who can insure the vehicle using the VIN number. 
    • Hey guys, looking for these side skirts if anyone can help me out. 
    • Wife and I are still looking for a new home. One condition was a large enough garage for a full-size lift in one bay. Now if only we could find something... We've been looking for almost a year now.
    • Thanks everyone for the ideas! Sadly, ramps are a no go for me. With young kids at home, I do most of my work late at night while they're sleeping. Starting the car multiple times wouldn't be a great idea.  I'll go see one of those new long reach low profile jacks and take a couple measurements to see if they will fit.   
×
×
  • Create New...